Dell Networking SONiC: IPv4 Address Resolution Protocol
요약: This article explains about IPv4 Address Resolution Protocol in Dell Networking SONiC. This article uses a switch running Dell SONiC 4.1.
이 문서는 다음에 적용됩니다.
이 문서는 다음에 적용되지 않습니다.
이 문서는 특정 제품과 관련이 없습니다.
모든 제품 버전이 이 문서에 나와 있는 것은 아닙니다.
지침
|
Prerequisites
We are using standard interface naming to demonstrate the Concepts. See Dell article 202172 Dell Networking S-Series: Basic Interface Configuration - SONiC 4.0 for more information regarding interface naming |
Index
Introduction
View IPv4 Address Resolution Protocol entries.
Clear IPv4 entries
Introduction
The Address Resolution Protocol (ARP) allows IPv4 packets to be sent across networks by translating IP network addresses to MAC hardware addresses, and MAC addresses to IP addresses. The MAC address and corresponding IP address of destination devices are maintained in the ARP table. Using the IP address, the ARP table allows the switch to quickly retrieve the associated MAC address, encapsulate the IP packet in a L2 frame, and transmit it over the network to a destination.View IPv4 ARP entries
To display ARP table entries, use the show ip arp command. To filter the output, specify an interface, port channel, or VLAN, an IP address in the format x.x.x.x, a MAC address, or a combination of more than one value to match. You can also display summary information and the IPv4 ARP entries in a specified VRF.Command Syntax
admin@DELLSONiC:~$ sonic-cli
DELLSONiC# configure
DELLSONiC(config)#show ip arp <[interface {Eth slot/port[/breakout-port] [summary] | PortChannel number [summary] | Vlan vlan-id [summary] | Management port-number [summary]}] [ip-address] [mac-address mac-address] [summary] [vrf vrf-name] > |
DELLSONiC# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.1xx.1.4 00:01:02:03:44:55 Eth1/3 - Dynamic Fwd 192.1xx.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 192.1xx.3.6 00:01:02:03:04:05 Vlan100 Eth1/2 Dynamic Fwd 10.11.48.2xx 00:01:e8:8b:44:71 Management0 - Dynamic Fwd 0.0.0.0 00:00:00:00:00:00 lo - Dynamic Fwd |
NOTE: The last ARP entry for the loopback IP address 0.0.0.0 may be entered from the SONiC NEIGH_TABLE of APPL_DB. To delete the entry, you must manually delete it from the REDIS_DB using the redis-cli or any other application that allows you to edit the REDIS_DB.
DELLSONiC# show ip arp interface Vlan 20 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd 20.0.0.5 00:11:22:33:44:55 Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp 20.0.0.2 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp mac-address 90:b1:1c:f4:9d:ba Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp summary Total Entries ------------- 2 |
DELLSONiC# show ip arp vrf Vrf_1 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd 20.0.0.5 00:11:22:33:44:55 Vlan20 Eth1/1 Dynamic Fwd |
Clear IPv4 entries
To delete dynamically learned IPv4 entries from the ARP table, use the clear ip arp command. To specify the entries to be deleted, enter an interface, port channel, or VLAN, an IPv4 address, or a combination to match. Enter force to delete statically configured ARP entries. Use the show ip arp command to verify that the IPv4 entries have been deleted. DELLSONiC# clear ip arp < [interface {Eth slot/port[/breakout-port] | PortChannel number | Vlan vlanid | Management port-number}] [ip-address] [vrf vrf-name]> |
DELLSONiC# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.168.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 192.168.3.6 00:01:02:03:04:05 Vlan100 Eth1/2 Dynamic Fwd 10.11.48.254 00:01:e8:8b:44:71 Management0 - Dynamic Fwd sonic# clear ip arp interface Vlan 100 sonic# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.168.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 10.11.48.254 00:01:e8:8b:44:71 Management0 - Dynamic Fwd |
해당 제품
PowerSwitch E3200-ON Series, Dell EMC Networking N3200-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5232F-ON, PowerSwitch S5248F-ON, PowerSwitch S5296F-ON, PowerSwitch Z9264F-ON, PowerSwitch Z9332F-ON, PowerSwitch Z9432F-ON문서 속성
문서 번호: 000218168
문서 유형: How To
마지막 수정 시간: 16 10월 2023
버전: 3
다른 Dell 사용자에게 질문에 대한 답변 찾기
지원 서비스
디바이스에 지원 서비스가 적용되는지 확인하십시오.