Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Configuring and Adding the Member VLANs

Control and member VLANS are configured normally for Layer 2. Their status as Control or Member is determined at the FRRP group commands.

For more information about configuring VLANS in Layer 2 mode, refer to the Layer 2 chapter.
Be sure to follow these guidelines:
  • All VLANS must be in Layer 2 mode.
  • Tag control VLAN ports. Member VLAN ports, except the Primary/Secondary interface, can be tagged or untagged.
  • The control VLAN must be the same for all nodes on the ring.

To create the Members VLANs for this FRRP group, use the following commands on all of the Transit switches in the ring.

  1. Create a VLAN with this ID number. CONFIGURATION mode. interface vlan vlan-id VLAN ID: the range is from 1 to 4094.
  2. Tag the specified interface or range of interfaces to this VLAN. CONFIG-INT-VLAN mode. tagged interface slot/port { range}
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    • Slot/Port, range : Slot and Port ID for the interface. The range is entered Slot/Port-Port.
  3. Assign the Primary and Secondary ports and the Control VLAN for the ports on the ring. CONFIG-FRRP mode. interface primary int slot/port secondary int slot/port control-vlan vlan id
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port. VLAN ID : Identification number of the Control VLAN.
  4. Configure a Transit node. CONFIG-FRRP mode. mode transit
  5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id { range} VLAN-ID, Range : VLAN IDs for the ring’s Member VLANs.
  6. Enable this FRRP group on this switch. CONFIG-FRRP mode. no disable

Califique este contenido

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
0/3000 characters
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Seleccione si el artículo fue útil o no.
  Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"