- Notes, cautions, and warnings
- Dell PowerEdge T630 server overview
- Converting the system from tower mode to rack mode
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions for converting system from tower to rack
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System feet
- Caster wheels – optional
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling-fan assembly (optional)
- System memory
- Flex bays
- Hard drives
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter
- Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter
- Installing a 3.5-inch hard drive adapter into a hot swap hard drive carrier
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Optical drives and tape drives
- Internal USB memory key (optional)
- Expansion card holder
- Expansion cards
- GPU card holder (optional)
- GPU cards (optional)
- Internal dual SD module (optional)
- Internal SD card
- Processors and heat sinks
- Power supply unit
- System battery
- Hard drive backplane
- SD vFlash card (optional)
- Control panel assembly
- System board
- Trusted Platform Module
- Power interposer board and power distribution board
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Dell PowerEdge T630 Owner's Manual
Serial Communication details
About this task
- Option
- Description
- Serial Communication
Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS. BIOS console redirection can also be enabled and the port address can be specified. This option is set to Auto by default.
- Serial Port Address
- Enables you to set the port address for serial devices.
This option is set to Serial Device 1=COM2, Serial
Device 2=COM1 by default.NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature. To use console redirection by SOL, configure the same port address for console redirection and the serial device.NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from within the BIOS setup utility may not always revert the serial MUX setting to the default setting of Serial Device 1.
- External Serial Connector
Enables you to associate the External Serial Connector to Serial Device 1, Serial Device 2, or the Remote Access Device by using this option.
NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by SOL, configure the same port address for console redirection and the serial device.NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from within the BIOS setup utility may not always revert this setting to the default setting of Serial Device 1.- Failsafe Baud Rate
- Specifies the failsafe baud rate for console redirection. The BIOS attempts to determine the baud rate automatically. This failsafe baud rate is used only if the attempt fails, and the value must not be changed. This option is set to 115200 by default.
- Remote Terminal Type
- Sets the remote console terminal type. This option is set to VT 100/VT 220 by default.
- Redirection After Boot
- Enables or disables the BIOS console redirection when the operating system is loaded. This option is set to Enabled by default.
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Geef een beoordeling (1-5 sterren).
Selecteer of het artikel nuttig is of niet.
Opmerkingen mogen geen speciale tekens bevatten: <>() \