Treceți la conținutul principal
Deconectare

Bun venit la Dell

Contul meu
  • Plasaţi comenzi rapid şi simplu
  • Vizualizaţi comenzile şi urmăriţi starea transportului
  • Creaţi şi accesaţi o listă cu produsele dvs.
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Autentificare Creaţi un cont Autentificare la Premier Autentificare la programul pentru parteneri
Contactaţi-ne

Dell PowerEdge R720 and R720xd Owner's Manual

PDF

Installing A Processor

  • CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
  • NOTE: If you are installing a single processor, it must be installed in socket CPU1.
  1. Before upgrading your system, download the latest system BIOS version from support.dell.com and follow the instructions included in the compressed download file to install the update on your system.
    • NOTE: You can update the system BIOS using the Lifecycle Controller.
  2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. When disconnected from the power source, press and hold the power button for three seconds to fully drain the system of stored power prior to removing the cover.
  3. Open the system.
  4. Remove the cooling shroud.
    • WARNING: The heat sink and processor are hot to the touch for some time after the system has been powered down. Allow the heat sink and processor to cool before handling them.
    • CAUTION: Never remove the heat sink from a processor unless you intend to remove the processor. The heat sink is necessary to maintain proper thermal conditions.
  5. Remove the heat sink/heat-sink blank and processor/processor blank, as applicable.
    • NOTE: The procedure to remove the heat-sink blank or processor blank is similar to removing a heat-sink or processor.
  6. Unpack the new processor.
  7. Align the processor with the socket keys on the ZIF socket.
    • CAUTION: Positioning the processor incorrectly can permanently damage the system board or the processor. Be careful not to bend the pins in the socket.
    • CAUTION: Do not use force to seat the processor. When the processor is positioned correctly, it engages easily into the socket.
  8. With the release levers on the processor socket in the open position, align pin 1 of the processor, using pin 1 position guide on the socket, as reference and set the processor lightly in the socket.
  9. Close the processor shield.
  10. Rotate the socket-release lever near the lock icon lock icon until it is locked in position.
  11. Similarly, rotate the socket-release lever near the unlock icon unlock icon until it is locked in position.
  12. Using a clean lint-free cloth, remove the thermal grease from the heat sink.
    • CAUTION: Applying too much thermal grease can result in excess grease coming in contact with and contaminating the processor socket.
  13. Open the grease applicator included with your processor kit and apply all of the thermal grease in the applicator to the center of the topside of the new processor.
  14. Place the heat sink on the processor.
  15. Using a #2 Phillips screwdriver, tighten the heat-sink retention sockets.
  16. Install the cooling shroud.
  17. Close the system.
  18. Reconnect your system and peripherals to their electrical outlets, and turn on the system.
  19. Press <F2> to enter the System Setup and check that the processor information matches the new system configuration.
  20. Run the system diagnostics to verify that the new processor operates correctly.

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\