Connectrix MDS-9710-V2

This document highlights minimum, recommended, and latest code versions for Dell Technologies Enterprise and Data Center Infrastructure products. Dell carefully evaluates and monitors code deployment data to ensure that product releases meet our stringent expectations to provide our customers with reliable products and solutions.

Information about customer replaceable unit (CRU) videos for Dell Technologies VxFlex Ready node products

Affected products after NX OS 9.4.2a upgrade: Cisco MDS 9000 NX-OS and SAN-OS Software, Cisco MDS 9100 Series Multilayer Fabric Switches, Cisco MDS 9200 Series Multiservice Switches, Cisco MDS 9300 Series Multilayer Fabric Switches, Cisco MDS 9500 Series Multilayer Directors, Cisco MDS 9700 Series Multilayer Directors

This article contains information about customer replaceable unit (CRU) videos for Dell Technologies VNX and VNXe products.

Information about customer replaceable unit (CRU) videos for Dell Technologies PowerProtect and Data domain products

Information about customer replaceable unit (CRU) videos for Dell Technologies Powerflex products

Information about customer replaceable unit (CRU) videos for Dell Technologies ECS products

Information about customer replaceable unit (CRU) videos for Dell Technologies Connectrix products

Error on switch %DAEMON-3-SYSTEM_MSG: error: protocol identification string lack carriage return

MDS-9710-V2 - Standby supervisor goes into powered-up state during In-Service Software Upgrade (ISSU).

This article provides steps to back up and restore Zones using DCNM.

This issue is seen when the audit logs are getting filled for the switches, receive notification email alerts from the switches, or when any switch is idle for some time and no events are generated.

This KB provides steps to collect switch #show tech-support through DCNM.

This issue can be triggered only if, while lower-numbered slot supervisor is in ha-standby state, it is pulled out of the chassis without issuing the command `out-of-service module x`.

Attempting to configure a /31 subnet mask on IPS interface for the MDS 9700 series directors and MDS 9220i switches generates an error stating 'Bad mask'.

The purpose of Smart Zoning is to reduce the amount of administrative overhead that is required to add new hosts to the SAN with the addition of a few keywords.

Learn how the MyService360 services analytics dashboard integrates the Dell AIOps (formerly CloudIQ) Health Score into the Install Base views. This integration streamlines services and product health management by IT admins using the MyService360 and Dell AIOps portals. Verify supported products by portal and access helpful Dell AIOps resources.

Downgrade from 8.5.1 to earlier 8.x versions fails to execute due to compatibility error in snmp config.

Domain IDs uniquely identify a switch in a Virtual Storage Area Network (VSAN). A switch may have different domain IDs in different VSANs. The domain ID is part of the overall Fibre Channel (FC) ID. The configured domain ID can be preferred or static. By default, the configured domain ID is 0 (zero) and the configured type is preferred. Domain IDs can range from 1 to 239. The 0 (zero) value can be configured only if you use the preferred option.

End devices unable to communicate - FCNS rejecting to all FC CT queries with 'logical busy'. Because end devices cannot get proper responses to their queries, they will not be able to communicate with one another.

When performing Connectrix MDS upgrade, the "install all" command returns the message "Pre-upgrade check failed. "Return code -1."

When third party security software run on MDS switches, they can report that MDS switches are accepting the TLS1.0 connections.

Connectrix MDS : 97xx Chassis information missing with error message %PLATFORM-2-PS_UNSUPPORTED

SCG, Base64 encoding, Cisco, ESRS script, password Base64 Encoding

On a zone activation, all HBAs zoned to a VPLEX front-end port are logged out and lose a path.

How to perform NX-OS upgrade on the MDS switches

F16_PLDA_RXBUF_MERR error on a single port ASIC results in a complete module reload.

SnakeLoobpack passed incorrect port range to module warning when SnakeLoopback could not identify faulty device.

Using the SSH name command shuts down the management0 interface. CAUTION: This causes loss of out of band connectivity to the switch

In a 32 Gbps MDS platform, %SYSMGR-3-HEARTBEAT_FAILURE the 'lc_port_mgr' service is randomly killed with signal 6, possibly multiple times.