VxRail E560N

Ce document met en évidence les versions de code minimum, recommandé et le plus récent pour les produits Dell Technologies Enterprise et Datacenter Infrastructure. Nous évaluons et surveillons scrupuleusement les données de déploiement de code afin de nous assurer que les versions de produits répondent à nos attentes les plus strictes visant à fournir à nos clients des produits et solutions fiables.

Cet article fournit des informations sur le dépannage du serveur PowerEdge pour les problèmes d’absence d’alimentation, d’échec de l’autotest de démarrage, d’absence de démarrage et d’absence de signal vidéo. La procédure concerne les serveurs lame, rack et tour.

Intermittent delays in the Redfish Application Programming Interface (API) response may prevent the VxRail 8.0.361 cluster from displaying the host Product Serial Number Tag (PSNT) and "Management IPV4" fields in the physical view page. You can trigger a system cache refresh on the VxRail Manager to restore the physical view display.

This procedure explains how to re-create a host management account.

L’iDRAC est le back-end d’ISM qui fournit des fonctionnalités de surveillance du matériel sur l’appliance VxRail. Cet article décrit les paramètres requis sur l’iDRAC.

This article outlines how to create a firmware baseline, view compliance reports, and apply updates in Dell OpenManage Enterprise.

Event code: VXR500ENC19 This event code indicates "<Enclosure Management Module Name> has failed."

Event code: VXR500AMP400 This event code indicates "The <sensor name> sensor has failed, and the last recorded value by the sensor was <current> A."

Event code: VXR500ENC21 This event code indicates "<Enclosure elements name> has been removed."

Event code: VXR500FAN0027 This event code indicates "The <sensor name> sensor has failed with a value of <fan speed> RPM."

Event code: VXR500FAN0013 This event code indicates "<fan name> RPM is less than the lower critical threshold."

Event VXR508SSD0002 triggers due to available spare being less than threshold value.

Event VXR500STOR393 is triggered due to: Auto-configure stacking is not allowed.

Attempting a copy-back operation on a non-unmap-capable drive triggers event code VXR500STOR375.

Cet article de la base de connaissances présente brièvement le code d’événement : VXR500FAN0016

Explore the Dell End of Service Life (EOSL) and End of Life (EOL) list for converged infrastructure, storage, and storage networking products. Access End-of-Life documents for hardware, software, and firmware release and service dates

Event VXR500STOR374 triggers due to a non-Unmap-capable drive being used for a rebuild operation.

Event code VXR508STOR373 is triggered due to a hot spare drive not supporting unmap when the virtual drive (VD) has it enabled.

Event Code VXR508STOR372 triggers due to unmap being disabled or not supported on the controller.

Event Code VXR508STOR371 indicates: Unable to use the physical drive arg1 because the drive selected is not unmap-capable for virtual drive configuration.

Event code: VXR500FAN0020 This event code indicates "The <fan name> is non-functional."

Event code: VXR500ENC23 This event code indicates "<enclosure name> - Issue with PHY <PHY data>."

Event code: VXR500AMP405 This event code indicates "The <sensor name> sensor state has changed to a failed state with a value of <current> A."

Event code: VXR500ENC3 This event code indicates "<Enclosure Name> is shutdown."

Event code: VXR500FAN8503 This event code indicates "The Chassis was turned off because more than two internal fans stopped functioning."

Event code: VXR500CBL0002 This event code indicates "Backplane <bay ID> signal cable disconnected."

Event code: VXR500CBL0006 This event code indicates "Unsupported backplane <bay ID> configuration: Multiple RAID controllers cannot be connected to the same backplane."

Event code: VXR500CBL0005 This event code indicates "Backplane <bay ID> <connector name> connector incorrectly connected to the motherboard SATA controller."

Event code: VXR500FAN0015 This event code indicates "<fan name> RPM is greater than the upper critical threshold."

VxRail: Event Code: VXR500ENC24 This event code indicates "Communication with <enclosure name> is intermittent."