PowerEdge RAID Controller H755 Adapter

本文按系列（代系）列出了适用于戴尔系统的 PowerEdge RAID 控制器 (PERC)。有几种类型的 PERC 控制器可用，具体取决于内部/外部存储接头、最大驱动器支持和 RAID 支持。

本文介绍如何将附加磁盘添加到虚拟磁盘或重新配置虚拟磁盘。

有关在启用固件设备顺序 （FDO） 的情况下如何在 Windows/VMware ESXi 安装中检测不到 PERC 后面的驱动器的信息。

本文介绍了使用戴尔支持页面打开服务请求 （SR） 的过程。 快速获取有关您的戴尔设备的帮助。不再需要等待。不再有技术难题。 戴尔让您可以轻松地修复问题、安排维修或获得支持，只需从您的设备或我们的支持网站即可。

本文介绍如何在 Windows 2022 安装期间加载 PERC 驱动程序。如果未加载 PERC 驱动程序，安装向导将无法找到存储位置

本文提供有关如何在 PowerEdge RAID 控制器 （PERC） 上将硬盘分配为全局热备份的说明

Linux host reports reduced storage performance when using PERC or HBA controllers with attached SSD or NVMe devices.

This article provides information about various battery error codes, their possible causes, and examples.

本文提供有关如何在系统设置 （F2） 菜单中导入外部配置 RAID 阵列的信息。

This article explains intermittent single-bit (SBE) and multi-bit (MBE) ECC error messages observed on PERC H750/H755/H755N controllers and one cause of these errors.

When attempting to save the PowerEdge RAID Controller (PERC) controller's event logs from within the Host Integrated Interface (HII), this process may take upwards of 20 minutes to complete.

此处回答有关 Dell PowerEdge RAID 控制器卡和驱动器操作的问题，并提供有教程。

This article provides information about how to manage the Dell PowerEdge RAID Controller (PERC) using the PERCCLI utility.

When encryption is enabled on BOSS-N1, the system may stop during POST with the message: "No Boot Device Available or Operating System Detected."

The "Predictive failure reported for disk x" error continues to be logged every 24 hours, even after the identified drive has been replaced. The issue only affects drives connected to PERC Controllers in RAID configuration.

Beginning with 15G PowerEdge, servers are offered in configurations that report more drive connections than are physically available.

This article describes the different type of controllers and the ways in which they should be reseated.

Slow insertion of a SAS or SATA drive in PowerEdge 15G or 16G Servers with a PERC or HBA controller configuration causes a "No Access" bit to be set, leading to an inability to blink and unblink drives.

将磁盘部署到包含 PowerEdge RAID 控制器 （PERC） H750 或 H755 存储控制器的任何目标时，虚拟磁盘顺序相反。

PERC11 controllers may report a status of "Needs Attention" in The Human Interface Infrastructure (HII) under Properties.

PowerEdge RAID Controller (PERC11, PERC10), Human Interface Infrastructure (HII) configuration utility, and iDRAC do not support array expansion.

This article provides information about how to boot past the Driver Health Manager Screen.

本文介绍如何在 PowerEdge 服务器的系统设置中检查虚拟磁盘属性。

本文介绍如何使用命令收集智能日志。

This article explains how to export the RAID controller log (TTYlog) directly from OpenManage Server Administrator (OMSA) using the interface or using the command lines.

This article explains how to create a Virtual Disk using the System Settings menu.

This article explains how to download, install, and use the Dell PowerEdge RAID Controller (PERC) Command-Line Interface (CLI) utility to manage your RAID controller. The utility is supported on PERC Series 8 and later family controllers on hosts running Windows, Linux, or ESXi. PERCCLI can also extract RAID controller logs which contain information that allows you or Dell Technical Support to determine the status of RAID controllers and the connected storage devices to narrow down possible sources of error.

This article provides information about the battery learn cycle. It consists of a controller performed battery calibration operation to periodically determine the condition of the battery. This operation cannot be disabled.

This article provides information about Double Faults and Punctures in a RAID array and it also advises how to fix the problem.

This article provides information about Intelligent Mirroring and Enhanced RAID 10.