Removal
Stand
Identify the stand highlighted in blue.
Press and hold down on the tab that secures the stand to the display assembly base.
Lift the stand off the display assembly base.
Back Cover
Identify the back cover highlighted in blue.
Place your palm in the middle of the back cover, and then pry the back cover from the display assembly base starting from the top corners.
Slide and lift the back cover off the display assembly base.
I/O Cover
Identify the I/O cover highlighted in blue.
Remove the screws that secure the I/O cover to the display assembly base.
Using a pry tool, pry open the corners and bottom of the I/O cover.
Lift the I/O cover off the display assembly base.
System Board Shield
Identify the system board shield highlighted in blue.
Remove the screws that secure the system board shield to the display assembly base.
Lift the system board shield off the display assembly base.
SSD 2230
Memory Module
Identify the memory module highlighted in blue.
Using your fingertips, carefully spread apart the securing clips on each end until the memory module pops up.
Slide and remove the memory module from the memory module slot.
Wireless Card
Identify the wireless module (WLAN) highlighted in blue.
Remove the screw that secures the wireless card bracket to the wireless card.
Remove the bracket to access the WLAN cables.
Disconnect the antenna cables from the WLAN.
Slide and remove the WLAN card from the connector.
Coin Cell Battery
Identify the coin cell battery highlighted in blue.
Push the release lever on the coin cell battery socket to release it from the socket.
Lift the coin cell battery from the socket.
Media Card Reader
Identify the media card reader highlighted in blue.
Remove the screw that secures the media card reader to the display assembly base.
Lift the latch and disconnect the media card reader cable from the system board.
Slide and remove the media card reader along with its cable from the slot.
System Board Assembly
Identify the system board assembly highlighted in blue.
Disconnect the backlight and fan cables from the system board assembly.
Disconnect the speaker and microphone module cables from the system board assembly.
Lift the latch and disconnect the power button board and display cables from the system board assembly.
Loosen the captive screw that secure the heatsink.
Remove the screws that secure the system board assembly to the display assembly base.
Remove the solid state drive screw mount that secures the system board assembly to the display assembly base.
Lift the system board assembly off the display assembly base.
Microphone Module
Identify the microphone module highlighted in blue.
Remove the screws that secure the microphone module to the display assembly base.
Peel the tape that secures the microphone module cable to the display assembly base.
Unroute and remove the microphone module cable from the routing guides on the display assembly base.
Lift the microphone module off the display assembly base.
Install
Microphone Module
Identify the microphone module location highlighted in blue.
Place the microphone module into the slot and align with screw holes.
Install the screws that secure the microphone module to the display assembly base.
Route the microphone module cable through the routing guides on the display assembly base.
Adhere the tape that secures the microphone module cable to the display assembly base.
System Board Assembly
Identify the system board assembly location highlighted in blue.
Install the system board assembly on the display assembly base and align the screw holes.
Install the screws that secure the system board assembly to the display assembly base.
Install the solid state drive screw mount that secures the system board assembly to the display assembly base.
Tighten the captive screw that secure the heat sink. Do not over tighten.
Connect the power button board and display cables on the system board assembly. Close the latch to secure.
Connect the backlight and fan cables on the system board assembly.
Connect the speaker and microphone module cables on the system board assembly.
Media Card Reader
Identify the heatsink assembly location highlighted in blue.
Place the media card reader along with its cable into the slot and align with screw holes.
Connect the media card reader cable to the system board. Close the latch to secure.
Replace the screw that secures the media card reader to the display assembly base.
Coin Cell Battery
Identify the coin cell battery location highlighted in blue.
Insert the coin cell battery into the socket with the positive side (+) label facing up.
Snap the battery in the socket.
Wireless Card
Identify the wireless module (WLAN) location highlighted in blue.
Insert the WLAN into the connector on the system board.
Connect the white cable to the main (white triangle).
Connect the black cable to the auxiliary (black triangle).
Install the bracket to secure the antenna cables.
Install the screw that secures the wireless card bracket.
Memory Module
Identify the memory module location highlighted in blue.
Align the notch on the memory module with the tab on the slot and slide the memory into the slot at an angle.
Press the memory module down until it clicks into place.
SSD 2230
System Board Shield
Identify the system board shield location highlighted in blue.
Place the system board shield on the display assembly base and align with screw holes.
Install the screws that secure the system board shield to the display assembly base.
I/O Cover
Identify the I/O cover location highlighted in blue.
Place the I/O cover on the display assembly base and align with screw holes.
Install the screws that secure the I/O cover to the display assembly base.
Back Cover
Identify the back cover location highlighted in blue.
Align the back cover to the display assembly base.
Press along the sides to snap the back cover into place on the display assembly base.
Stand
Identify the stand location highlighted in blue.
Align the stand to the slot with the display assembly base.
Insert the stand into place into the slot on the display assembly base.