Removal
System Cover
Identify the system cover highlighted in blue.
Rotate the latch release lock counter clockwise to the unlocked position.
Open the latch on the system cover
Slide system cover toward the back and using the latch lift system cover up from system.
Cooling Shroud
Identify the cooling shroud highlighted in blue
Holding the touch points, lift the cooling shroud away from the system.
Cooling Fan Assembly
Identify the cooling fan assembly highlighted in blue.
Lift the release levers to unlock the cooling fan assembly from the system.
Hold the release levers, and lift the cooling fan assembly away from the system.
Power Supply Units (PSU)
Identify the power supply unit (PSU) highlighted in blue
Press the orange release latch and slide the PSU out of the system by using the PSU handle
Riser 1
Identify the expansion card riser 1 highlighted in blue.
Holding the slots on the expansion card riser, lift the riser from the riser connector on the system board
Riser 2
Identify the expansion card riser 2 highlighted in blue
Grip the release tab and lift the riser from the riser connector on the system board
Riser 3
Identify the expansion card riser 2 highlighted in blue
Grip the release tab and lift the riser from the riser connector on the system board
Internal Dual SD Module
Identify the internal dual SD module (IDSDM) highlighted in blue
Locate the blue pull tab on the internal dual SD module
Pull up on the blue pull tab and lift the IDSDM out of the system
System Memory
Identify and locate the system memory highlighted in blue
To release the memory module from the socket, simultaneously press the ejectors on both ends of the memory module socket.
Lift and remove the memory module from the system.
Network daughter card
Identify the network daughter card (NDC) highlighted in blue
Loosen the captive screws that secure the network daughter card to the system board.
Hold the NDC by the edges on either side of the touch point, and lift the card to disengage it from the connector on the system board.
Slide the NDC away from the back of the system until the ethernet connectors are clear of the slot in the back panel.
Lift the NDC out of the chassis.
PCIe Card Holder
Identify the PCIe card holder highlighted in blue
Press the release tab and slide the card holder toward the back of the chassis to release the PCIe card holder from the chassis.
Lift the PCIe card holder out of the chassis
Cable Retention Bracket
Heatsink
Identify the heatsink highlighted in blue
Loosen one of the captive screws that secure the heat sink to the system board.
Allow some time (approximately 30 seconds) for the heat sink to loosen from the processor.
Remove the screw diagonally opposite to the screw that you first loosened.
Repeat step 2 and 3 for loosening the remaining two screws.
Remove the heat sink
Remove the thermal grease from the heat sink and processor by using the alcohol wipe provided
Processor
Identify the processor highlighted in blue
Release the open first socket lever near the unlock icon by pushing the lever down and out from under the tab.
Release the close first socket release lever near the lock icon by pushing the lever down and out from under the tab.
Lower the open first socket-release lever to lift the processor shield.
Hold the tab on the processor shield and lift the processor shield until the open first socket-release lever lifts up.
Lift the processor out of the socket and leave the open first socket-release lever up.
System Board
Identify the system board highlighted in blue
Disconnect all cables from the system board.
Hold the system board holder, lift the blue release pin, lift the system board, and then slide it toward the front of the chassis.
Lift the system board out of the chassis.
Install
System Board
Identify the system board location highlighted in blue
Unpack the new system board assembly.
Holding the system board holder and release pin, lower the system board into the chassis.
Push the system board toward the back of the chassis until the board clicks into place
Processor
Unpack the new processor.
Identify the processor location highlighted in blue
Align the pin-1 triangle indicator on the processor with the triangle on the system board, carefully place the processor in the socket.
Close the processor shield.
Lower the 'close first' socket-release lever near the lock icon and push it under the tab to lock it.
Similarly, lower the 'open first' socket-release lever near the unlock icon and push it under the tab to lock it.
Heatsink
Identify the heatsink location highlighted in blue
Use the thermal grease syringe included with your processor kit to apply the grease in a thin spiral on the top of the processor.
Place the heat sink onto the processor.
Tighten the four screws to secure the heat sink to the system board in a diagonal pattern
Cable Retention Bracket
PCIe Card Holder
Identify the PCIe card holder location highlighted in blue
Align the PCIe card holder with the notches and tabs on the power supply unit cage.
Press the release tab and slide the PCIe card holder toward the front of the chassis until firmly seated.
Network daughter card
Identify the network daughter card (NDC) location highlighted in blue
Orient the NDC so that the ethernet connectors fit through the slot in the back panel.
Align the captive screws on the card with the captive screw sockets on the system board.
Press the touch points on the card until the card connector is firmly seated on the system board connector.
Tighten the captive screws to secure the NDC to the system board.
System Memory
Identify the system memory location highlighted in blue, refer to system cover
Press the levers on the memory module socket outward to allow the memory module to be inserted into the socket.
Align the edge connector of memory module with the alignment key of the memory module socket, and insert the memory module in the socket.
Press the memory module until the socket levers firmly click into place.
Internal Dual SD Module
Identify the internal dual SD module (IDSDM) location highlighted in blue
Align the IDSDM connector with the connector on the system board
Press the IDSDM into the connector
Riser 3
Identify the expansion card riser 2 location highlighted in blue
Lower the riser into the system until the riser connector engages with the connector on the system board
Riser 2
Identify the expansion card riser 2 location highlighted in blue
Lower the riser into the system until the riser connector engages with the connector on the system board
Riser 1
Identify the expansion card riser 1 location highlighted in blue.
Align the guide rails on the riser with the standoffs on the side of the system
Lower the riser into the system until the riser connector engages with the connector on the system board
Power Supply Units (PSU)
Identify the power supply units (PSU) location highlighted in blue
Slide the PSU into the system until the PSU is fully seated and the release latch snaps into place
Cooling Fan Assembly
Identify the cooling fan location highlighted in blue.
Align the guide rails on the cooling fan assembly with the standoffs on the system.
Lower the cooling fan assembly into the system until the cooling fan connectors engage with the connectors on the system board
Press the release levers to lock the cooling fan assembly into the system.
Cooling Shroud
Identify the cooling shroud location highlighted in blue
Align the tabs on the cooling shroud with securing slots on the system, then lower the cooling shroud into the system until firmly seated.
System Cover
Identify the system cover location highlighted in blue
Align the slots on the system cover with the tabs on the system.
Push the system cover latch down. The system cover slides forward and the slots on the system cover engage with the tabs on the system.
Rotate the latch release lock clockwise to the locked position.