- Notes, cautions, and warnings
- About your system
- Initial system configuration
- Configuring enclosure components
- Installing enclosure components
- Recommended tools
- Front bezel (optional)
- System feet—tower mode
- Wheel assembly (optional)—tower mode
- System cover
- Inside the system
- Hard drives
- Removing a 2.5 inch hard drive blank
- Installing A 2.5 Inch Hard-Drive Blank
- Removing a 3.5 inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Removing a hot-swap hard drive
- Installing a hot-swap hard drive
- Removing a hard drive from a hard drive carrier
- Installing a hard drive or solid state drives into a hard drive carrier
- Server modules
- Server module partitions
- Power supply units
- Cooling shroud
- Cooling fans
- Cooling fan assembly
- Blower modules
- I/O module
- Optical drive (optional)
- CMC cards
- PCIe cage
- Expansion cards
- Expansion card installation guidelines
- Expansion card operational power status
- PCIe slot indicators
- Removing a low profile expansion card
- Installing a low profile expansion card
- Removing the low profile expansion card divider unit
- Installing the low profile expansion card divider unit
- Removing a full height expansion card
- Installing a full height expansion card
- Removing the full-height expansion card divider unit
- Installing the full height expansion card divider unit
- Removing the expansion card riser
- Installing the expansion card riser
- Double-wide GPGPU card (optional)
- Integrated storage controller cards
- Shared PERC 8 External card
- System battery
- System top and base covers
- Mounting ears
- Control panel assembly
- Backplane expander boards
- Hard drive backplane
- Power distribution board
- System board
- Power pass-through board
- Midplane
- Converting the system from tower mode to rack mode
- Troubleshooting your system
- Responding to a systems management alert message
- Troubleshooting external connections
- Troubleshooting a damaged enclosure
- Troubleshooting enclosure components
- Troubleshooting a wet enclosure
- Troubleshooting power supply units
- Troubleshooting power supply unit mismatch
- Troubleshooting blower modules
- Troubleshooting the system battery
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting an optical drive
- Troubleshooting a storage controller
- Troubleshooting hard drives
- Troubleshooting expansion cards
- Troubleshooting the I/O module
- System board connectors
- Technical specifications
- Enclosure dimensions and weight — Tower
- Enclosure dimensions and weight — Rack
- Server module specifications
- Expansion bus specifications
- Power specifications
- Drive specifications
- Chassis Management Controller specifications
- Enclosure control panel specifications
- I/O Module specifications
- Environmental specifications
- Expanded operating temperature
- Getting help
Dell PowerEdge VRTX Enclosure Owner's Manual
Installing enclosure components
NOTE: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift
the system by yourself.
NOTE: Exercise
care when removing or installing components when the system is on,
to avoid the risk of electric shock.
CAUTION: To maintain
optimum thermal conditions, ensure that there are no obstructions
to airflow on the front and back of the enclosure. The front and back
of the enclosure must have at least 30 cm (12-inches) and 61 cm (24
inches) of unobstructed space respectively.
NOTE: To ensure proper operation
and cooling, all bays in the enclosure must be populated at all times
with either a module or with a blank.
NOTE: It is recommended that
you remove the front bezel, server modules, hard drives, and power
supply units from the chassis to reduce weight, before laying the
enclosure on its side.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\