Reference Guide Dell Wyse ThinOS Release 8.3.1 – INI Files

Parameter

* Global overrides identically-named user profile

** After sign off, user profile returns to global value

Default is no.

Yes/no option to disable the new cache mechanism allowing more memory to be available to a user. This is developed with Citrix Presentation Server 4.0 and Windows Server. If set to no, the new cache mechanism is enabled.

Default is no.

Yes/no option to use an alternate IP address returned from an ICA master browser to get through firewalls. This setting in a wnos.ini file will be saved into NVRAM if EnableLocal=yes is set in the wnos.ini file.

RDP Only.

Default is yes.

Yes/no option to enable RDP auto detect network feature. When this option is set to yes the Optimize for low speed link and the Desktop Experience options are disable by default.

**AutoSignoff={ no, yes}

[Shutdown={ no, yes}]

[Reboot={ no, yes}]

Default is no.

AutoSignoff —Yes/no option to automatically sign-off a user when the last opened session is closed.

Shutdown — Default is no. Yes/no option to shut down the thin client. If shutdown is set to yes, the ShutdownCounter value is used to control the count-down before the system is turned off.

Reboot — Default is no. Yes/no option to reboot the thin client. If Reboot is set to yes, the ShutdownCounter value is used to control the count down before the system is rebooted.

Default is no.

Yes/no option to clear the TSCAL license stored in the non-volatile memory. It can be replaced by FixLicense=clean.

Connect — Connection protocol. Follow the ICA option list, see Table 8: ICA Connect Options or RDP option list, see Table 9: RDP Connect Options . Any options you use for your connection must be on the same logical line; \can be used for line continuation, see Rules and Recommendations for Constructing the INI Files.

ConnectionBroker={ default, Microsoft, Quest, VMware}

Default is default.

Specifies the Connection Broker type. Select VMware to enable VDM XML support. If you enter VMware, the VMware logo appears on the login screen.

For Dell vWorkspace broker, ConnectionBroker=Quest is recommended.

*Device=Ethernet

[Speed={ Auto, 10M HD, 10M FD, 100M HD,

100M FD, or 1000M}

[MTU=mtu]

[KeepAlive={1-600}]

[Warning={ no, yes}]

[StaticIPWaitFileServer={ 0-255}]

Device — Specifies to use an Ethernet.

Speed — Default is auto. Specifies the ethernet speed to either Auto, 10MHD, 10M FD, 100M HD, 100M FD, or 1000M. If Speed is set in a wnos.ini file, the Speed statement in the {username}.ini file will be disabled.

MTU — A maximum transmission unit value between 500 to 1500.

KeepAlive — Specifies a time value in seconds between 1 and 600 to keep an idle connection alive.

device=ethernet keepalive=20 warning=yes

StaticIPWaitFileServer — Default is 0. Specifies the timeout threshold in seconds for cases of static IP.

Device=vusb

[ForceRedirect=DeviceID]

[ForceLocal=DeviceID]

[Type={TCX, HDX}]

[InterfaceRedirect={ no, yes}]

Device — Specifies the ID of a local USB device that is not redirected by default.

ForceRedirect — Specifies a forced redirect of the local USB device to the server. This parameter has priority over ForceLocal.

Device=vusb ForceRedirect=0x04f2,0x0112,0x03,0x01,0x01

Device=vusb Type=HDX

InterfaceRedirect — Default is no. Yes/no option to enable part of a composite device to run locally and part of the device to run on a remote session.

Device=Wireless

[Mode={Infrastructure, AdHoc}]

[SSID=ssid Channel={1-14}]

[WepKey={ None, 1-4}]

[Key1=k1]

[Key2=k2]

[Key3=k3]

[Key4=k4]

[Key1Enc=key1 encrypted]

[Key2Enc=key2 encrypted]

[Key3Enc=key3 encrypted]

[Key4Enc=key4 encrypted]

[RoamSensitive={high, medium, low}]

[Algorithm={Open, SharedKey}]

[DisableBand={ None, 2.4G, 5G}]

[PreferBand={None, 2.4G, 5G}]

[Priority=ssid_list]

[DisableN={ no, yes}]

[DisableWlan={yes, no, EnetUp}]

Device — Defines the wireless Ethernet device remotely and saves to the local NVRAM. Not all options are needed. For example, you can define Key1 to have a key of k1 and leave out Key2 through Key4.

device=wireless SSID=THINOS RoamSensitive=low

k1 to k4 are any real values of 5 to 13 characters or 10 to 26 Hex digits. Encrypted keys will overwrite unencrypted keys. Thus, if Key1 and Key1Encare both configured, then Key1Enc will overwrite Key1.

RoamSensitive — Defines the sensitivity level of wireless roaming with respect to launching the Roaming daemon:

high - signal lower than -60 dBm

medium - signal lower than -70 dBm

low - signal lower than -80dBm

The RoamSensitive parameter is also used to enable wireless roaming. If it is not configured in the INI file, roaming will never be launched even if the signal is lower than -80dbm, unless it totally loses a wireless signal.

Algorithm — Specifies the authentication method of WEP between ThinOS and the access point. If set to Open, open authentication will be selected. If set to ShareKey, shared key authentication will be selected.

DisableBand — Default is None. Use to disable 2.4G or 5G 802.11 band.

PreferBand —This parameter is used to set the priority of wireless connection band, and select the 2.4G or 5G access point to connect. Default is None.

Priority — sets the priority of wireless profiles. The ssid list is separated by a semicolon or comma and the priority is from high to low.

DisableN — Default is no. Yes/no option to disable 802.11n Wi-Fi wireless networking.

DisableWlan— Used to disable the wireless connection. If DisableWlan=EnetUp, and the Ethernet is on while booting, the wireless connection is disabled.

Device=Wireless Mode=Infrastructure SSID=ThinIsIn
                                                IEEE8021X=yes network=wireless profile=ThinIsIn access=WPA2-ENT
                                                eap=yes eaptype=EAP-PEAP peapeap=EAP-MSCHAPV2
                                                Device=Wireless Mode=Infrastructure SSID=wtos_95 roamsensitive=high
                                                IEEE8021X=yes network=wireless profile=wtos_95 access=WPA2-ENT
                                                eap=yes eaptype=EAP-PEAP peapeap=EAP-MSCHAPV2
                                                Device=Wireless Mode=Infrastructure SSID=wtos_11n
                                                IEEE8021X=yes network=wireless profile=wtos_11n access=WPA2-PSK
                                                wpa2pskpwd=2wsx3edc
                                                Device=Wireless Priority="wtos_11n,wtos_95,ThinIsIn"
                                             

**EnableLocal={ no, yes}

[HideDefault={ no, yes}]

Default is no.

Yes/no option to enable locally configured entries to show in the Connect Manager list. When connections defined in local NV-RAM are displayed in the Connect Manager, they are marked with an asterisk.

HideDefault — Default is no. Yes/no option to hide the default ICA and RDP connections that are present on the devices.

*EthernetSpeed={ Auto, 10M HD, 10M FD, 100M HD, 100M FD, 1000M}

Default is auto.

EthernetSpeed — Specifies the Ethernet Speed to either Auto, 10M HD, 10M FD, 100M HD, or 100M FD. Once specified, it is saved in the non-volatile memory. This parameter can be replaced by the Device and Speed parameters.

Fastconnect={yes, no}

[Key={F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, Pause/Break}]

[Ctrl={yes, no}]

[Alt={yes, no}]

[Connect={ICA, RDP, PCoIP}]

[List={*|app1|server1;app2}]

[Title={*_seamless_window_title*]

If you set the parameter to yes, press the special key to launch specified desktop or published application. If the desktop or published application is available, pressing the key brings it to the foreground.

If you set to no, the followed options are ignored and disables fast connect functions. The followed options need to be configured to one or several fast connect setting.

The option Key specifies the fast connect key.

The option Ctrl specifies whether the Control key is combined or not, for fast connect key.

The option Alt specifies whether the Alt key is combined or not, for fast connect. The option Connect specifies the protocol of fast connecting session.

The option List specifies the connecting list of the desktop or published application. It supports wildcards * to match the session host/application or description. Also it supports a list separated by ; or ,.

The option Title specifies the seamless window name. It supports wildcards * to match the window name. For a seamless window, it is needed because seamless windows share session. It uses List option to match session and uses the option Title to match the seamless window.

For example,

fastconnect=yes \

key=F1 ctrl=no alt=no connect=ica list="Excel 2013" title="*Excel*" \

key=F2 ctrl=yes alt=no connect=ica list="XA76-2008R2*".

When you press F1, the application Excel 2013 is launched. If there is a seamless window which matches the title *Excel* in this session, the seamless window is brought to the foreground, else it is launched.

When you press Ctrl+F2, the desktop XA76-2008R2* is launched. If the desktop is available, it is brought to the foreground.

[CtrlKey={yes, no}]

[PowerButton=signoff]

Default value is no.

If the value is set to yes, pressing the F12 (default) key or the key defined in FastDiconnectKey= statement will close the active window of the session. If the active window is a seamless window, the action will only close the window. If the window is not a seamless window, then the session will be disconnected.

If the option CtrlKey and/or AltKey is set to yes, then the function key should be combined with Ctrl key and/or Alt key.

For PCoIP session, press Ctrl+Alt+F12 key combination to disconnect the session unless FastDisconnect=no is configured. This combined disconnect key is compatible with other platforms such as P25 and Linux.

If the value is set to Signoff, pressing the F12 (default) or the key defined in FastDisconnectKey= statement will disconnect all sessions and return to the signon window.

If PowerButton is set to signoff, pressing the power button of the unit after you sign on will disconnect all sessions and return to the logon window. Otherwise, the unit will shutdown normally.

FastDisconnectKey={F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, Pause\Break}

FixLicense={Factory, clean, yes, no, OldFormat}

Default is no.

Specifies the option to replace the TSCAL license stored in the non-volatile memory.

Default is no.

Yes/no option to hide the information of the connection host or IP. Some examples include:

- When moving a mouse cursor over the connection icons on the desktop, a balloon help pop-up displays ‘…’ instead of the host name.

- When a Reconnect to a connection message or an ICA error message window displays, the connection description displays instead of host name.

- When moving a mouse cursor over the PN icon, the connected PN servers do not display.

Specifies the file name of the hosts. This file is a simple text file that associates IP addresses with hostnames, one line per IP address. The length of the file name is limited to 63 characters.

The file must be placed in file server and can be cached if set MirrorFileServer=yes in the wnos.ini.

When resolving a host name, the system will initially look in the file and if not found, will search DNS, WINS, and so on. The following is an example of format in the hosts file:

10.151.122.1 gateway.ctx.com

10.151.122.123 myvm.ctx.com

Default is http.

Establishes the default browsing protocol. This setting can be overridden by the parameter HttpBrowsing in each connection property. The method of browsing selected must match the method provided by the server(s) being accessed.

This setting in a wnos.ini file will be saved into NVRAM, if EnableLocal=yes is set in the wnos.ini file.

IEEE8021X={yes, no}

network={wired, wireless}

[Profile=ssid]

[access={WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT}]

[eap={yes, no}]

[servervalidate={yes, no}]

[servercheck={yes, no}]

[servername={"servername for EAP-TLS, EAP-PEAP, EAP-FAST"}]

[eaptype={ None, EAP-LEAP, EAP-TLS, EAP-PEAP, EAP-FAST}]

[leapun={username for EAP-LEAP}]

[leappwd={password for EAP-LEAP}]

[leappwdEnc={password encrypted for EAP-LEAP}]

[tlsauthtype={user, machine}]

[tlsclntcert={client certificate filename for EAP-TLS}]

[tlsclntprikey={filename of certificate with private key for EAP-TLS}]

[tlsclntprikeypwd={password for private key}]

[tlsclntprikeypwdEnc={password encrypted for private key}]

[peapeap={EAP-MSCHAPV2, EAP-GTC}]

[peapidentity={identity/username for PEAP}]

[peapmschapun={username for EAP-PEAP/ EAP-MSCHAPV2}]

[peapmschappwd={password for EAP-PEAP/EAP-MSCHAPV2}]

[peapmschappwdEnc={password encrypted for EAP-PEAP/EAP-MSCHAPV2}]

[peapmschapdm={domain for EAP-PEAP/ EAP-MSCHAPV2}]

[peapmschaphidedm={yes,no}]

[peapsinglesignon={yes, no}]

[peapgtcun={username for EAP-PEAP/ EAP-GTC}]

[peapgtcpwd={password for EAP-PEAP/ EAP-GTC}]

[peapgtcpwdEnc={password for encrypted for EAP-PEAP/EAP-GTC}]

[wpapskpwd={passphrase for WPA-PSK}]

[wpapskpwdEnc={passphrase encrypted for WPA-PSK}]

[wpa2pskpwd={passphrase for WPA2-PSK}]

[wpa2pskpwdEnc={passphrase encrypted for WPA2-PSK}]

[encryption={TKIP|CCMP}]

[fasteap={EAP-MSCHAPV2, EAP-GTC}]

[fastidentity={Identity for EAP_FAST}]

[fastmschapun={username for EAP-FAST/EAP-MSCHAPV2}]

[fastpmschappwd={password for EAP-FAST/EAP-MSCHAPV2}]

[fastmschappwdEnc={password encrypted for EAP-FAST/EAP-MSCHAPV2}]

[fastmschapdm={domain for EAP-FAST/EAP-MSCHAPV2}]

[fastmschaphidedm={yes,no}]

[fastsinglesignon={yes, no}]

[fastgtcun={username for EAP-FAST/EAP-GTC}]

[fastgtcpwd={password for EAP-FAST/EAP-GTC}]

[fastgtcpwdEnc={password for encrypted for EAP-FAST/EAP-GTC}]

**Inactive={ 0, to 480} (minutes)

[NoSessionTimer=0-480]

Default is 0.

Specifies that if there is no keyboard or mouse use in the configured time in minutes, it will sign off or shutdown or reboot depending on AutoSignoff= …

If NoSessionTimer is set, then when there is an active sessions, use this timer to replace the Inactive value.

AutoSignoff=yes [Shutdown=yes] [Reboot=yes]

IPProto=ICMP

[DisableTStamp={yes, no}]

[DisableEcho={yes, no}]

Configures the ICMP protocol.

DisableTStamp — If DisableTStamp=yes, the system will not reflect the ICMP timestamp (13) request.

DisableEcho — If DisableEcho=yes, the system will not reflect the ICMP echo (8) request. In this case, the unit cannot be pinged.

Default is no.

Yes/no option to enable optimization for low speed connections, such as reducing audio quality or decreasing protocol-specific cache size or both.

This setting in a wnos.ini file will be saved into NVRAM, if EnableLocal=yes is set in the wnos.ini file.

MMRCodecConfig=AUDIO

[disableac3={ no, yes}]

[disablempeg={ no, yes}]

[disablewma1={ no, yes}]

[disablewma2={ no, yes}]

[disablewma3={ no, yes}]

[disablemp3={ no, yes}]

[disablepcm={ no, yes}]

MMRCodecConfig — Only for platforms with TCX Multimedia . Specifies the audio to allow the disabling of the various codec options when playing audio.

disableac3 — Default is no. Yes/no option to disable the ac3 codec when playing audio.

disablempeg — Default is no. Yes/no option to disable the mpeg codec when playing audio.

disablewma1 — Default is no. Yes/no option to disable the wma1 codec when playing audio.

disablewma2 — Default is no. Yes/no option to disable the wma2 codec when playing audio.

disablewma3 — Default is no. Yes/no option to disable the wma3 codec when playing audio.

disablemp3 — Default is no. Yes/no option to disable the mp3 codec when playing audio.

disablepcm — Default is no. Yes/no option to disable the pcm codec when playing audio.

MMRCodecConfig=VIDEO

[disablempeg1={ no, yes}]

[disablempeg2={no, yes}] [disablejpeg={no, yes}]

[disablewmv1={ no, yes}]

[disablewmv2={ no, yes}]

[disablewmv3={ no, yes}]

MMRCodecConfig — Only for platforms with TCX Multimedia . Specifies the video to allow the disabling of the various codec options when playing video.

disablempeg1 — Default is no. Yes/no option to disable the mpeg1 codec when playing video.

disablempeg2 — Default is yes. Yes/no option to disable the mpeg2 codec when playing video.

disablejpeg — Default is no. Yes/no option to disable the jpeg codec when playing video.

disablewmv1 — Default is no. Yes/no option to disable the wmv1 codec when playing video.

disablewmv2 — Default is no. Yes/no option to disable the wmv2 codec when playing video.

disablewmv3 — Default is no. Yes/no option to disable the wmv3 codec when playing video.

Default is no — Enables compression.

Yes/no option to turn off compression. To turn off compression, enter yes. Used here this parameter is a global statement for all connections. It sets the default value of NoReducer.

OneSignServer=onesign_server

[DisableBeep={ no, yes}

[KioskMode={ no, yes}]

[EnableFUS={ no, yes}]

[TapToLock={0, 1, 2}]

[EnableWindowAuthentication={ yes,no}]

[AutoAccess={VMW,XD,XA}]

[NetBIOSDomainName={ no, yes}]

OneSign virtual desktop access offers a seamless authentication experience and can be combined with single sign-on for no click access to desktops and applications in a virtual desktop environment.

The following inputs are acceptable values:

https://ip

or

https://FQDN

DisableBeep — Default is no. Yes/no option to set the Rfideas reader to mute when a card is tapped.

KisokMode — Default is no. Yes/no option to allow the OneSign user to share the client desktop.

EnableFUS — Default is no. Yes/no option to set the Citrix client to remain running when switch users.

TaptoLock — Default is 2. Only active when KioskMode=yes. Specifies tap to lock.

If TapToLock=0, then tap a card to lock terminal is disabled. If TapToLock=1 (Tap to lock), then use the proximity card to lock the terminal.

If TapToLock=2 (Tap over), then lock the terminal and log in a different user.

EnableWindowAuthentication — Default is yes. Yes/no option to sign-on with the user’s Windows credentials to pre-defined broker if the OneSign sign-on fails.

AutoAccess — Specifies the corresponding type of broker to automatically start. If not defined, the broker type is obtained from the Imprivata Server setting of the computer and user policy. If none of them is defined, then the first available broker server from the Imprivata server is started.

NetBIOSDomainName — Default is no. Yes/no option to enable the authentication to the broker server using the NetBIOS domain name. If set to yes, the Imprivata domain list will show NetBIOS domain name and the card user will authenticate to the broker server using the NetBIOS domain.

PnliteServer=<List of {IP address, DNS names, or URLs} >

[ReconnectAtLogon={ 0, 1, 2}]

[ReconnectFromButton={ 0, 1, 2}]

[AutoConnectList={*/ appname1;appname2; appname3...}]

[timeout=5…300]

[CAGRSAAuthMethod={LDAP, RSA}]

[CAGAuthMethod={LDAP, RSA}]

[CAGAuthMethod={LDAP+RSA, RSA+LDAP}]

[RequestIconDataCount={0-65535}]

[DefaultSettings={XenApp, XenDesktop}]

[SmartcardPassthrough={ yes, no}]

[StoreFront={ no, yes}]

PnliteServer=List of {IP address, DNS names, or URLs}

PnliteServer — Specifies the list of IP addresses or host names with optional TCP port number or URLs of PNAgent/PNLite servers. The list is empty by default.

Each entry with optional port is specified as Name-or-IP:port, where port is optional; if not specified, port 80 is used as the default.

If a port other than 80 is used, the port number must be specified explicitly with the server location in the form IP:port or name:port. Once specified, it is saved in the non-volatile memory.

The statement PNAgentServer and Web interface for Citrix MetaFrame Server is equal to this statement.

ReconnectAtLogon — Specifies the reconnection function at log in.

Default is 0 — disables the option.

1 — reconnects to disconnected sessions only.

2 — reconnects to active and disconnected sessions.

ReconnectFromButton — Specifies the reconnection function from the reconnect command button.

Default is 0 — disables the option.

1 — reconnects to disconnected sessions only.

2 — reconnects to active and disconnected sessions.

AutoConnectList — Specifies the PNA applications that will be automatically started when using PNA to sign on. If AutoConnectList=*, then all the PNA applications will be automatically connected.

The autoconnectlist is the connection description of application or host name which can use the wildcard * to match the string.

Timeout — Specifies the time in seconds where a client will try to establish a connection before reporting that it is unreachable.

CAGRSAAuthMethod or CAGAuthMethod — CAGAuthMethod option is used for CAG authentication configuration.

RequestIconDataCount — RequestIconDataCount is used for requesting 32-bit color icons. It is a counter which means that only the count of the icons will be requested. The default number is 10.

For example, if set RequestIconDataCount=0, no icon data will be requested. If set RequestIconDataCount=5, only 5 icons are requested.

DefaultSettings — Specifies the default settings for XenApp or XenDesktop.

Xen App Default Settings:

1. SignOn=Yes

2. PnliteServer= RequestIconDataCount=20

3. desktopcolordepth=32

4. LongApplicationName=yes

5. sessionconfig=ica progressivedisplay=yes ondesktop=yes

6. device=audio volume=high

7. Seamless=yes FullscreenReserved=yes

8. sessionconfig=all mapdisks=yes

9. Enabled by default: Disks, Serials, Sound

10. Disabled by default: USB, Printers, Smart Cards

Xen Desktop Default Settings:

1. SignOn=Yes

2. sysmode=vdi toolbarclick=yes toolbardelay=3

3. sessionconfig=ica progressivedisplay=yes

4. PnliteServer=

5. AutoSignoff=yes

6. Enable by default: Printers, Serials, USB, Sound

7. Disabled by default: Disk, Smart Cards

SmartcardPassthrough — Default is yes. Yes/no option to enable/disable the smartcard pass through mode.

StoreFront — Default is no. Yes/no option to support Citrix StoreFront Authentication. The value will be saved into NVRAM.

RTPTosDscp={Default/CS1/CS2/CS3/CS4/CS5/CS6/CS7/AF11/AF12/AF13/AF22/AF23/AF31/AF32/AF33/AF42/AF43}

Recommended for use under Customer Support direction for troubleshooting purposes. Specifies where the ThinOS event logs will be saved.

**Seamless={ no, yes}

[HideTaskbar={ 0, 1, 2, 3}]

[FullscreenReserved={ no, yes}]

Seamless — Default is no. Yes/no option to set the default resolution for ICA published applications to Seamless for ICA connection parameters.

HideTaskbar — Default is 0. Specifies the status of the taskbar when maximizing the seamless window.

0 — Do not hide the taskbar.

1 — Taskbar will be hidden when maximizing the seamless window to full screen. Moving the mouse over the lowest bottom of the screen will display the taskbar. This setting excluding the FullscreenReserved parameter in a wnos.ini file will be saved into NVRAM if EnableLocal=yes is set in the wnos.ini file.

SecureMatrixServer=<SecureMatrix Server

Host name or IP address/FQDN or URL>

[EnableSelectTable]

Specifies the Host name or IP address/FQDN or URL of the Secure Matrix server. Http or https protocol usage is decided by the server configuration. If SecureMatrixServer is defined, the user must pass authentication with the Secure Matrix server first, and then there is a seamless log in to the brokers if the server can provide the correct broker credentials, if not, the user must enter broker credentials to log in.

For Example: SecureMatrixServer=https://gsb01.bjqa.com

EnableSelectTable enables you to select the table type (3 or 4 tabs) when you change the password (SMXBridge server 3.9 start supports this feature). Default value is No.

SelectGroup={ no, yes}

[Default=default_desc]

description=group1

[groupname=name1]

[description=group2]

[groupname=name2]

Default is no.

SelectGroup — Yes/no option to allow a user to select from a group list on the Log on dialog box during a log in. If yes, the description will display in the group list box.

groupname — The group name is used to identify the group including the directory and file name. If not defined, the description will become the group name.

The Default option following "SelectGroup=yes" can specify the default group. The value is one of group description defined after that. After you select another group and sign off, this default group will be selected.

If default option is not specified, the last selected group will be selected in the next sign on.

For example:

SelectGroup=yes \
                                                	default="Sus team" \
                                                	description="Dev team" groupname=dev \
                                                	description="Sus team" \
                                                	description="SQA team" groupname=sqa \
                                                	description="guest"
                                             

Group 1: Description="Dev team" groupname=dev

The file \wnos\ini\dev\dev.ini must be created in the file server. In the dev.ini, the broker, domain list, or connections can be defined for the dev team.

Group 2: .Description="Sus team"

The file \wnos\ini\Sus team\Sus team.ini must be created in the file server. In the Sus team.ini, the broker, broker list, or connections can be defined for the Sus team.

Group3...4...n...and so on.

After a user selects a group, the system will load the group ini file first, and then load the \wnos\ini\{group_name}\username.ini. If the username.ini in the group directory is not found, it will attempt to load \wnos\ini\username.ini as before.

Because the group list may define different brokers, the SelectServerList statement will be invalid if set SelectGroup=yes.

Serial={ COM1, COM2, COM3, COM4}

[Baud={1200, 2400, 4800, 9600, 19200,

38400, 57600, 115200}]

[Parity={None, Even, Odd}]

[Stop={1, 1.5, 2}]

[Size={5, 6, 7, 8}]

[Flow={None, XON/XOFF, CTS/RTS, Both}]

[Touch={ no, yes}]

[Touch_XYReverse={ no, yes}]

[Touch_type={ elo, microtouch, fastpoint}]

Serial — Default is COM1. Specifies the local serial ports configuration.

Baud — Specifies the local serial port baud rate.

Parity — Specifies the local serial port parity.

Stop — Specifies the local serial port stop.

Size — Specifies the local serial port size.

Flow — Specifies the local serial port flow.

Touch — Default is no. Yes/no option to denote that a serial touch screen is attached.

Touch_XYReverse — Default is no. Yes/no option to denote a reversal of the X and Y coordinates which are needed for some touch screens.

Touch_type — Default is elo. Specifies the type of touchscreen being used.

**SessionConfig=ALL

[unmapprinters={ no, yes}]

[unmapserials={ no, yes}]

[smartcards={ no, yes}]

[mapdisks={ no, yes}]

[disablesound={ no, yes}]

[unmapusb={ no, yes}]

[DisksReadOnly={ no, yes}]

[MouseQueueTimer={0–99}]

[WyseVDA={ no, yes}]

[WyseVDA_PortRange=startPort, endPort]

[UnmapClipboard={ no, yes}]

[DefaultColor={0,1,2}]

[VUSB_DISKS={yes, no}]

[VUSB_AUDIO={yes, no}]

[VUSB_VIDEO={yes, no}]

[VUSB_PRINTER={yes, no}]

[FullScreen={ no, yes}]

[Resolution={ default, vga_resolution}]

[DisableResetVM={ no, yes}]

[WyseVDAServerPort=serverPort]

[FontSmoothing={ yes, no}]

[AutoConnect={ yes, no}]

[MultiMonitor={ yes, no}]

[EnableImprivataVC={ yes,no}]

[Locale=LocaleID]

[SessionLogoffTimeout=seconds]

[GroupSession={yes, no}]

SessionConfig — Specifies the default settings of the optional connection parameters for all sessions.

unmapprinters — Default is no. Yes/no option to un-map printers.

unmapserials — Default is no. Yes/no option to un-map serials.

smartcards — Default is no. Yes/no option to use smartcards.

mapdisks — Default is no. Yes/no option to map disks.

disablesound — Default is no. Yes/no option to disable sound.

unmapusb — Default is no. Yes/no option to un-map USBs.

DisksReadOnly — Default is no. Yes/no option to mount mass storage disks as read-only.

MouseQueueTimer — Specifies the default queue timer of a mouse event in an ICA or RDP session (in 1/100 of a second). It can be used to adjust the bandwidth of a network.

WyseVDA — Default is no. Yes/no option to enable Virtual Desktop Accelerator for all ICA and RDP sessions.

WyseVDA_PortRange — Sets the ThinOS VDA client port range. The port range must follow these rules:

1. The port range is a list of start port and end port separated by a semicolon (;) or a comma (,).

2. Both ports must be between 1 and 65535.

3. The end port must be greater than start port.

For example, WyseVDA_PortRange=3000,3010, the start port is 3000, the end port is 3010.

UnmapClipboard — Default is no. Yes/no option to disable clipboard redirection for all sessions. For ICA and RDP, specifies if redirecting the clipboard. This setting in wnos.ini will be saved into nvram, if EnableLocal parameter is set to yes in wnos.ini.

DefaultColor — Specifies the default color depth to use for the session 0=256, 1=High color, 2=True Color.

VUSB_DISKS, VUSB_AUDIO, VUSB_VIDEO, and VUSB_PRINTER — Default no. Specifies if these USB devices will be redirected to the server using TCX Virtual USB or ICA or RDP USB redirection. By default, these devices are set as local devices.

FullScreen — Default is no. Specifies the default screen mode. When using FullScreen in a Dual Screen mode, the session will be displayed in Span mode

Resolution — Default is default. Specifies the session resolution. For example, 640 x 480 and other supported resolutions.

Default will set the resolution to the native resolution of the monitor. Setting the resolution to a value smaller than the native resolution of the monitor, will allow the session in Windowed mode. The resolution value cannot be higher than the native resolution.

DisableResetVM — Default is no. Set DisableResetVM=yes to disable Reset VM function. As default, this function is controlled by the server side is enabled including VMware View or Citrix PNA.

WyseVDAServerPort — Sets Wyse VDA Server Port for a ThinOS VDA client. The default port is 3471. The port range must be from 1029 to 40000. For example, WyseVDAServerPort=3000, sets VDA server port to 3000 and the client will connect to the VDA server using this port.

FontSmoothing — Default is yes. Set no to disable font smoothing.

AutoConnect — Default is yes. Set no to disable auto connect function.

MultiMonitor — Default is yes. Sets a multiple monitor layout. Set MultiMonitor=no to disable multiple monitor layout function. The session has the same desktop width and height with local virtual desktop size, spanning across multiple monitors, if necessary.

EnableImprivataVC— Default is yes. If set to no, the Imprivata Virtual Channel is disabled. The user can use vusb redirect instead of Imprivata Virtual Channel mode to use the Rfideas or finger print device in session as server side remote device.

[Locale=LocaleID]— Set Locale=LocaleID to set Locale in session for localization configuration to work. For information about LocaleID, refer to link msdn.microsoft.com/en-us/library/windows/desktop/dd318693(v=vs.85).aspx.

SessionLogoffTimeout—Setting SessionLogoffTimeout value forces all sessions to logoff when user signs off from the broker. The default value is 0 which retains the same behavior as before, and also disconnects the sessions. If you set a value, for example 30 seconds, broker sign-off waits for 30 seconds for all sessions to finish logoff, then, automatically session logs off. Broker sign-off will continue. During the waiting process, one notice prompts for user to check whether the session stops working if something is not saved. This feature currently supports Citrix Xen broker sessions and View Broker sessions only.

GroupSession=yes— Set to enable the function of grouping sessions and the menu item of Group Sessions is checked when you right click on the desktop. The default value is no and the original state of Group Sessions is unchecked.

**SessionConfig=ICA

[desktopmode={ fullscreen, window}]

[mapdisksunderz] : DISCONTINUED. DO NOT USE.

[TosIpPrecedence={0–5}]

[TosDscp={Default/CS1/CS2/CS3/CS4/CS5/CS6/CS7/AF11/AF12/AF13/AF22/AF23/AF31/AF32/AF33/AF42/AF43}]

[DiskMapTo=a character sequence]

[SysMenu={remote, local}]

[SessionReliability={ no, yes}]

[WarnPopup={ yes, no}]

[ondesktop={ no, yes, all, none, desktops, applications}]

[AudioQuality={ default, high, medium, low}]

[USBRedirection={TCX, ICA|HDX}]

[ZLKeyboardMode={0, 1, 2}]

[ZLMouseMode={0, 1, 2}]

[SucConnTimeout=seconds]

[HDXFlashUseFlashRemoting={Never,Always}]

[HDXFlashEnableServerSideContentFetching={Disabled,Enabled}]

[EnableRTME={ Yes, No}]

[FlipByTimer={ 0, 1}]

[RefreshTimeOut={dd:hh:mm}]

[Timeout={Yes, No}]

[PasswordExpireNotify={yes, no}]

[RefreshPopupNotice={yes, no}]

SessionConfig — Specifies the ICA default settings of the optional connection parameters for all ICA sessions.

desktopmode — Default is fullscreen. Specifies the display mode of an ICA published desktop when using an ICA PNAgent logon; the default is fullscreen mode for a PNA desktop application .

mapdisksunderz — DISCONTINUED. DO NOT USE.

TosIpPrecedence — Allows you to set IP Precedence in the TOS fields.

TosDscp — Sets IP DSCP in the TOS fields.

DiskMapTo — Specifies to map disks to a character sequence.

SysMenu — Default is local. Specifies the system menu mode when right-clicking the taskbar button of a seamless window. If it is remote, the system menu will come from the remote server; otherwise, it will be the local menu.

SessionReliability — Default is no. Yes/no option to enable session reliability.

WarnPopup— If WarnPopup=no, the option can disable the warning message when session reliability happens in order to decrease the administrative support calls.

ondesktop — Default is no. Specifies options for displaying connection icons on the desktop:

1. If AutoConnectList is set in the PNLiteServer statement, all connections configured in AutoConnectList parameter will display on the desktop.

2. Default is no and means that the property of ondesktop will be controlled by the server. However, the connections are still always added to the Connect Manager list and PNA menu list.

3. In cases other than no, the connection is controlled by the local thin client. If set so that the connection icon does not display on the desktop, the connection icon will not be added to the Connect Manager list and the PNA menu list.

all — same as yes, display all connections on desktop.

none — do not display any connections.

desktops — only display connections on desktop.

applications — only display applications, the connections will be handled as an ondesktop_list. For example, if you set ondesktop=word; excel, then only the applications word and excel will be displayed.

AudioQuality — Default is default. Specifies the audio quality of ICA sessions.

USBRedirection — Default is ICA|HDX. Option to select the channel of usb devices redirection. This option is recommended to replace the older setting device=vusb type={TCX, HDX}.

ZLKeyboardMode — Specifies to accelerate the display of the input text on the client device over a high latency connection. 0=off, 1=on, 2=auto

ZLMouseMode — Specifies to accelerate the visual feedback for mouse-clicks on the client device over a high latency connection. 0=off, 1=on, 2=auto

SucConnTimeout— This option will enhance the seamless session share. During the first session logon, immediately start second or later sessions, which will wait for the time set with SucConnTimeout (or the logon success) to make sure new applications share with the first logon session.

HDXFlashUseFlashRemoting— Default is Always, which means the HDX is enabled always. The value Never is to disable HDX.

HDXFlashEnableServerSideContentFetching— Default is Disabled, which means the server side fetching content is not enabled. The value enabled is to enable this function.

EnableRTME— This option controls the launch of RTME service. The default value is enabled.

FlipByTimer— This option selects the screen refresh method. For some old server, there is no EndOfFrame transferred to the client. Then we can use this option to fix such issues.

RefreshTimeOut—RefreshTimeOut triggers auto-refresh which updates ICA applications automatically. The value format dd:hh:mm, indicate days&&hours&&minutes as the auto-refresh interval. The default value is 0, that disables auto-refresh.

Timeout– This option controls the credential prompt after ICA broker logon was timeout. Session ticket is invalid now. If yes, users have to enter their credential to re-login to launch session, if no, ThinOS will use the default credential to do login in background. The default is yes.

PasswordExpireNotify —This option enables the password expire notification, which should configure in storefront server side, Authentication, password change set as At any time. Then before the password expires, logon prompts a message displaying the number of days after which the password will expire and let you change the password. The option WarnPopup=no can disable the warning message when session reliability happens to decrease the administrative support calls.

RefreshPopupNotice — This option enables or disables the popup notice during refresh in progress. The default value is yes.

SessionConfig=PCoIP

[USBRedirection={ PCoIP, TCX}]

[ShowDisconnectMessage={ yes, no}]

[ShowReconnectMessageTime=seconds]

[ResumeTimeout=seconds]

SessionConfig — Specifies the PCoIP default settings of the optional connection parameters for all PCoIP sessions.

USBRedirection — Default is PCoIP. Specifies the channel of USB devices redirection.

ShowDisconnectMessage — Default is yes. Yes/no option to display a disconnect message when a session is disconnected. If set to yes, the message is displayed; if set to no, the message will only show in the Event Log.

ShowReconnectMessaageTime— This option specifies the number of seconds to show the session reconnect message box after the session detects the network congest. The default value is 50 seconds.

ResumeTimeout—The option ResumeTimeout specifies the number of seconds to wait after the reconnection dialog box prompts, and before the session successfully reconnects. If timeout value is reached then the session is closed. The default value is 1200 seconds.

**SessionConfig=RDP

[MaxBmpCache={128 to 1024}]

[DefaultColor={0,1,2}]

[EnableNLA]={no, yes}]

[ForceSpan={ no, yes}]

[EnableTSMM={ yes, no}]

[EnableGFX]={yes, no}]

[EnableVOR={ yes, no}]

[EnableRdpH264]={ yes, no}]

[EnableRecord={ yes, no}]

[EnableRFX={ yes, no}]

[USBRedirection={ TCX, RDP}]

[RDPScreenAlign4={yes, no}]

[WallPaper={ yes, no}]

[Dragging={ yes, no}]

[Animation={ yes, no}]

[Theme={ yes, no}]

[TosIpPrecedence={0-5}]

[TosDscp={Default/CS1/CS2/CS3/CS4/

CS5/CS6/CS7/AF11/AF12/AF13/AF22/AF23/

AF31/AF32/AF33/AF42/AF43}]

[AutoDetectNetwork={ yes, no}]

[TSGWEnable={ yes, no}]

SessionConfig — Specifies the RDP default settings of the optional connection parameters for all RDP sessions.

MaxBmpCache — Specifies the maximum bitmap cache number. This impacts the memory usage of an RDP session.

DefaultColor — Specifies auto (0), 16-bit (1), and 32-bit (2) options.

EnableNLA — Default is yes. Yes/no option to utilize the Network Level Authentication feature in RDP 7.

ForceSpan — Default is no. Yes/no option to disable RDP Multi Monitor feature.

EnableTSMM — Default is yes . Yes/no option to enable RDP7 Multi-media redirect.

EnableGFX —The option when set to yes, enables RDP8 Pipelined Graphics feature. Default is yes for all platforms other than Wyse 3010 thin client with ThinOS (T10). If this option is configured as no, the option EnableVOR and option EnableRdpH264 will be internally set to no despite of the settings in INI.

EnableRdpH264— Default is yes. This option enables RDP8.1 h.264 graphics feature. This option is internally set to no if the option EnableGFX is set to no manually or by default.

EnableRecord — Default is yes . Yes/no option to enable RDP feature of recording from local.

EnableRFX — Default is yes. Yes/no option to enable Bitmap Codec RemoteFX. Supported on R10L, Wyse 5010 thin client with ThinOS (D10D), Wyse 5010 thin client with PCoIP (D10DP), Wyse 5060 thin client with ThinOS, and Wyse 5060 thin client with PCoIP.

USBRedirection — Default is TCX . Option to select the channel of USB devices redirection.

RDPScreenAlign4 — Default is no. RDPScreenAlign4=yes can force RDP session width to 4 pixels aligned.

For example:

SessionConfig=RDP MaxBmpCache=1024 DefaultColor=1 EnableNLA=yes ForceSpan=yes EnableTSMM=no EnableRecord=yes EnableRFX=no
                                                RDPScreenAlign4=no
                                             

The options WallPaper, Dragging, Animation and Theme can set the RDP experience. Default is yes.

TosIpPrecedence — Allows you to set IP Precedance in the TOS fields.

TosDscp — Sets IP DSCP in the TOS fields.

AutoDetectNetwork —Default is yes. Yes/no option to enable an RDP session to adapt its data transfer to band width of network.

TSGWEnable — Default is yes. Yes/no option to obtain/enable TS gateway for the applications and desktops from Microsoft RDS broker server. The default value is yes which means that the TS Gateway setting is automatically obtained or enabled from the Microsoft RDS broker server.

Configures the retransmission of a TCP connection. The default value of this option is 5.

[reboot={yes, no}]

[Capital={yes, no}]

User can set a string up to 15 characters as terminal name. It can be configured as system variable like $MAC, $SN or $IP etc.

If reboot is set to yes and the terminal name is changed, the terminal will reboot.If "TerminalName=$DNS" is set, the system will do reverse DNS lookup to configure the terminal name. For example, if the DNS server configures the terminal IP as reverse dns name p12345.wysespt.com, the terminal name will be configured as p12345. If you set Capital=yes, the terminal name is capitalized.

VDIBroker=vdi_broker_url

[AutoConnectList={*|host1;host2;host3…}]

VDIBroker — Specifies the VDI broker server; supports both http and https.

If the vdi_broker_url does not start with http or https, the default protocol used is http. For an https connection, only one URL is accepted.

AutoConnectList — Specifies the VDI or VDM host which will be automatically started when using VDI or VDM sign-on. If the value is *, all of the VDI or VDM hosts will automatically be connected. The autoconnectlist is the connection description which can use the wildcard * to match the string.

Specifies the Virtual Center Server that supports both http and https. If the virtual_center_url does not start with http or https, the default protocol used is http.

**VNCPrompt={no, yes}

[{Accept, Reject}={ 10 to 600} (seconds)]

[ViewOnly={ no, yes}]

[ActiveVisible={ no, yes}]

Default is yes.

VNCPrompt — Yes/no option to enable a VNC shadowing prompt to a user. VNCPrompt set to yes means the user will always be prompted before shadowing starts and the user will then decline or accept VNC shadowing;

VNCPrompt set to no means the user will not be able to decline or accept shadowing. See also MaxVNCD in Table 4 : Connection Settings for wnos.ini files only to enable VNC shadowing.

See also VncPassword in Table 4: Connection Settings for wnos.ini Files Only to specify a string of up to 8 characters as the password used for shadowing.

Accept, Reject — Default is 10. Specifies the amount of time (in seconds) a user has to accept or reject the VNC shadowing prompt before the client desktop is shadowed.

ViewOnly — Default is no. Yes/no option to specify that the desktop being shadowed can only be viewed by the person who is shadowing; no keyboard or mouse events are allowed to interfere with the thin client being shadowed.

ActiveVisible — Default is no. Yes/no option to display a VNC session-end notice after the VNC session ends.

VPN=openconnect

[Description=string_description]

[Server=server_ip_or_name]

[Username=username_string]

[Password=password_string]

[Autoconnect={yes, no}]

The INI parameter openconnect enables you to connect to Cisco AnyConnect VPN servers, that use standard TLS protocols for data transport.

Description— Specifies the session name. The length of the string is limited to 21 characters.

Server— Specifies the VPN server IP or the VPN server name. The length of the string is limited to 63 characters.

Username— Specifies the login username. The length of the string is limited to 31 characters.

Password— Specifies the login password. The length of the string is limited to 31 characters.

Autoconnect— Specifies the option to enable or disable auto-connect on system startup.