- Notes, cautions, and warnings
- Dell PowerEdge M830 (for PowerEdge VRTX) system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- UEFI iSCSI Settings
- System Security
- Secure Boot Custom Policy Settings
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing server module components
- Safety instructions
- Recommended tools
- Removing and installing a server module
- System cover
- Inside the server module
- Cooling shroud
- Processor blank and DIMM blank
- System memory
- PCIe mezzanine cards
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Processors
- Hard drives or SSDs
- Hard drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x4) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x2) SATA hard drive or SSD plus 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x12) SAS SSD backplane
- Installing a 1.8-inch (x12) SAS SSD backplane
- System battery
- Storage controller card
- Expander card
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Dell PowerEdge M830 (For Dell PowerEdge VRTX Enclosure) Owner's Manual
Choosing the system boot mode
System Setup enables you to specify one of the following boot modes for installing your operating system:
- BIOS boot mode (the default) is the standard BIOS-level boot interface.
- Unified Extensible Firmware Interface (UEFI) (the default) boot mode is an enhanced 64-bit boot interface. If you have configured your system to boot to UEFI mode, it replaces the system BIOS.
- From the System Setup Main Menu, click Boot Settings, and select Boot Mode.
- Select the boot mode you want the system to boot into.CAUTION: Switching the boot mode may prevent the system from booting if the operating system is not installed in the same boot mode.
- After the system boots in the specified boot mode, proceed to install your operating system from that mode.
NOTE:
- Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot mode.
- For the latest information about supported operating systems, go to Dell.com/ossupport.
Forneça as classificações (de 1 a 5 estrelas).
Forneça as classificações (de 1 a 5 estrelas).
Forneça as classificações (de 1 a 5 estrelas).
Selecione se o artigo foi útil ou não.
Os comentários não podem conter estes caracteres especiais: <>()\