This post is more than 5 years old
4 Posts
1
19932
How do I reboot a data mover?
I'm a Celerra newbie and for the life of me cannot find an option to reboot a data mover. Can I do this through the Celerra Manager web interface or the Navisphere web interface? There is no problem with the equipment but I am in the process of qualifying the Celerra where I work and one of my functional tests is that the data mover boots without error but I can't find a way to "gracefully" reboot it.
Also, is there a quick log I can view that shows the boot up process that I would be able to use as proof that it booted error free?
Thanks in advance.
Also, is there a quick log I can view that shows the boot up process that I would be able to use as proof that it booted error free?
Thanks in advance.
nandas
1.5K Posts
0
June 16th, 2009 08:00
Welcome to the EMC support forums.
You can reboot a data mover through Celerra Web Manager or from Command Line (CLI).
In Celerra Manager - Under "Data Movers" - select the server_x on the right pane and right click on it to select "Reboot".
Using CLI - the command is
server_cpu server_x -reboot now
to shutdown the data mover, in place of reboot you can choose -halt.
However, using these options do not initiate a data mover failover - so you have to be absolutely careful on a production environment.
You may consider failing over the data mover to standby data mover - which will reboot the original data mover in the process to failover to the standby data mover.
In other words, if server_2 is running on slot_2 and slot_3 is the standby one - failover server_2 so that it now runs on slot_3 and slot 2 gets rebooted. The command will be
server_standby server_2 -activate mover
When you fail back from slot 3 to slot 2 - server_2 is back on data mover 2 (slot_2) and slot_3 gets rebooted - the command will be
server_standby server_2 -restore mover.
Please refer to the "Celerra Network Server System Operations" document available on Powerlink or User Documentation CD for more details.
Hope this helps,
Regards,
Sandip
Message was edited by: Updated the process of rebooting using Celerra Manager
Sandip
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
June 16th, 2009 08:00
if you just want to reboot it, click on datamovers tab in Celerra Manager, right click on datamover and select reboot. What are you trying to test ?
dbernero1
4 Posts
0
June 16th, 2009 09:00
Is there a log file that will show that the reboot of the data mover is successful?
nandas
1.5K Posts
1
June 16th, 2009 09:00
server_cpu server_x -reboot -monitor now
This will provide you the status of the reboot process with "done" when completed.
Also use /nas/sbin/getreason command to ensure that the data mover is rebooted and in contacted state.
You may also see the following codes as the Data Mover or blade reboots:
0 (reset) ¿ Data Mover or blade performing a power on self-test (POST)
1 (DOS booted) ¿ Data Mover or blade booting to DOS
3 (loaded) ¿ operating system loaded and initializing
4 (ready) ¿ operating system initialized
5 (contacted) ¿ Data Mover or blade available
Lastly - you may look at Control Station System Logs: /nas/log/sys_log - for getting this type of logs - for a data mover reboot - you may find a message from logged by "BoxMonitor" stating that a slot is rebooted - ensure the status ends with (1) at the end which confirms successfull reboot - for example
Jun 11 1:19:27 2009 BoxMonitor:6:45 Slot 3 has rebooted. (1)
Hope this helps.
Sandip
Message was edited by:
Sandip
cosse
26 Posts
1
June 16th, 2009 11:00
This will show you the current status of the datamovers. Fully booted datamovers look like this:
5 - slot_2 contacted
5 - slot_3 contacted
5 - slot_4 contacted
5 - slot_5 contacted
5 - slot_6 contacted
5 - slot_7 contacted
5 - slot_8 contacted
5 - slot_9 contacted
You want the first colum to be a 5 and the status to say contacted.
Sorry, just saw that Sandip already posted this.
Message was edited by:
cosse
nandas
1.5K Posts
0
June 16th, 2009 11:00
Thanks,
Sandip
dbernero1
4 Posts
0
June 16th, 2009 11:00