Unsolved
This post is more than 5 years old
3 Posts
0
53018
6224 general or trunk mode
Hi
I am having a bit of a mare getting a pair of stacked 6224s trunking VLAN information with an HP gbe2c blade module. What I need to achieve:
- Two tagged VLANs 101 and 102 tagged through to the HP switch and in turn tagged right down to a blade with the server software used to present virtual interfaces on each VLAN. HP config clearly not for this forum, this for info only.
- Since this is a flat network, i.e. everything else is untagged VLAN1, need to pass untagged traffic right the way through too
On the Powerconnect, I have read lots of posts regarding untagged VLAN 1 traffic and trunk ports on the 6224. It seems whatever I am doing wrong that untagged traffic doesn't get through when using a trunk port, i.e. on the uplink ports to either side of the gbe2c
However, if I set the uplink ports as switchport mode general then all I get is default VLAN (i.e. untagged traffic - it seems anyway). I need both together (untagged VLAN1 and tagged VLAN 101 and 102).
Uplink interface now to the gbe2c:
interface ethernet 1/g12
witchport mode general
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101-102 tagged
exit
interface ethernet 3/g12
switchport mode general
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101-102 tagged
exit
As above, untagged traffic is now passed (as opposed to when I used a trunk port) but the other switch doesn't 'see' the VLANs, i.e. I have
interface vlan 101
name "xxxxxx"
routing
ip address 172.16.10.254 255.255.255.0
exit
interface vlan 102
name "xxxxx"
routing
ip address 172.17.10.254 255.255.255.0
exit
But I can't reach either address above from the HP.
If you spot anything that precludes VLANs 101 or 102 being tagged correctly on these ports in above config would appreciate it since this is driving me mad! Or if there is a way with a trunk port to pass untagged traffic that would also work.
At least if I can find out one side of the equation is right can take it from there...
TIA
Zeee
bh1633
909 Posts
0
May 2nd, 2009 04:00
enable routing globally on the PowerConnect stack.
console> enable
console# configuration
console(config)# ip routing
If that is not your problem, please post your entire config and any other information you have.
zee2009
3 Posts
0
May 2nd, 2009 05:00
Thanks for your reply. Complete config:
!Current Configuration:
!System Description "Dell 24 Port Gigabit Ethernet, 2.1.0.13, VxWorks5.5.1"
!System Software Version 2.1.0.13
!
configure
vlan database
vlan 101-102
vlan association subnet 172.16.10.0 255.255.255.0 101
vlan association subnet 172.17.10.0 255.255.255.0 102
exit
stack
member 1 1
member 3 1
exit
ip address 192.168.0.2 255.255.250.0
ip name-server 192.168.0.10
ip name-server 192.168.0.11
ip routing
ip route 0.0.0.0 0.0.0.0 192.168.0.254
interface vlan 101
name "St1"
routing
ip address 172.16.10.254 255.255.255.0
exit
interface vlan 102
name "St2"
routing
ip address 172.17.10.254 255.255.255.0
exit
username "itsupport" password level 15 encrypted
no spanning-tree
!
interface ethernet 1/g1
channel-group 1 mode auto
exit
!
interface ethernet 1/g2
channel-group 1 mode auto
exit
!
interface ethernet 1/g3
channel-group 2 mode auto
exit
!
interface ethernet 1/g4
channel-group 2 mode auto
exit
!
interface ethernet 1/g11
switchport mode general
switchport general pvid 101
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101
exit
!
interface ethernet 1/g12
switchport mode general
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101-102 tagged
exit
!
interface ethernet 3/g1
channel-group 1 mode auto
exit
!
interface ethernet 3/g2
channel-group 1 mode auto
exit
!
interface ethernet 3/g3
channel-group 2 mode auto
exit
!
interface ethernet 3/g4
channel-group 2 mode auto
exit
!
interface ethernet 3/g12
switchport mode general
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101-102 tagged
exit
!
interface port-channel 1
switchport mode trunk
switchport trunk allowed vlan add 1,101-102
exit
!
interface port-channel 2
switchport mode trunk
switchport trunk allowed vlan add 1,101-102
exit
exit
Ports 1 -2 and 3-4 on switch 1 and 3 in the stack are into a storage device (EMC Celerra) to which the tagging works fine. The Celerra allows tagging VLAN1, when I tried the same config into the blade chassis switch (HP gbe2c) it didn't work, don't think it likes tagging VLAN1. Hence trying general mode port to allow untagged and tagged traffic in.
ethernet 1/g11 is a physical server NIC in that VLAN - works fine.
Ports 12 on switch 1 and 3 go to the HP blade chassis. Currently it cannot see VLAN 101 or 102, unable to ping 172.16.10.254 from within the chassis. It is processing untagged traffic fine, can see LAN ok. Am trying to ascertain if there is something broken above or if it's on the blade switch the issue(s) exist.
Thanks again
Zee
bh1633
909 Posts
0
May 3rd, 2009 07:00
I think it is the blade server switch.
Please post the output of "show vlan".
zee2009
3 Posts
0
May 3rd, 2009 08:00
Thanks once again for replying, much appreciated.
Show VLAN output below:
VLAN Name Ports Type Authorization
----- --------------- ------------- ----- -------------
1 Default ch1-24, Default Required
1/g3-1/g24,
1/xg3-1/xg4,
3/g3-3/g24,
3/xg3-3/xg4
101 St1 ch1-2, Static Required
1/g11-1/g12,
3/g12
102 St2 ch1-2,1/g12, Static Required
3/g12
console#
Thanks again!
Zee
bh1633
909 Posts
0
May 3rd, 2009 13:00
I do not see anything obvious, so I will just tell you how I think 1/g12 and 1/g13 are behaving and maybe you can figure out if this is what you expect:
interface ethernet 1/g12
switchport mode general
no switchport general acceptable-frame-type tagged-only
switchport general ingress-filtering disable
switchport general allowed vlan add 101-102 tagged
exit
- will egress tagged vlan 102 and 103 traffic.
- will ingress tagged vlan 102 and 103 traffic
- I believe the pvid is set to 1 by default, so untagged egress traffic will be treated as a vlan 1 traffic
- I am not sure what happens to vlan 1 egress traffic on this port. I think this port will not egress vlan 1 traffic, so you should explicitly add it to vlan 1 untagged if that is your intention.
Regarding not being able to ping the PowerConnect interfaces from the HP chassis, is there a route to the PowerConnect switch from the blades? Can you ping the PowerConnect switch from the blade server switches? Can you ping the blade server switches from the blade servers?