Unsolved
This post is more than 5 years old
5 Practitioner
•
274.2K Posts
0
1677441
PowerConnect Common Example Commands
Example Commands
*The following are examples of what command. Please reference the owner's manual to confirm what commands you should run to perform a specific task.
Ports can be disabled using the following commands:
console# config
console(config)# interface ethernet g5
console(config-if)# shutdown
Enable a port using the following command:
console(config-if)# no shutdown
Creating LAGs – Static Two-port LAG
console> enable
console# configure
console(config)# interface range ethernet g1-2
console(config-if)# channel-group 1 mode on
console(config-if)# exit
console(config)#
Creating LAGs – Dynamic LACP LAG
console> enable
console# configure
console(config)# interface range ethernet g1-2
console(config-if)# channel-group 1 mode auto
console(config-if)# exit
console(config)#
Creating VLANs
console> enable
console# config
console(config)# vlan database
console(config-vlan)# vlan 2
console(config-vlan)# exit
console(config)# interface vlan 2
console(config-if)# name Marketing
console(config-if)# end
Change Management VLAN
console > enable
console# configure
console(config)#ip address vlan 5
Removing VLANs
console> enable
console# config
console(config)# vlan database
console(config-vlan)# no vlan 2
Remove Port From VLAN
console> enable
console# config
console(config)# interface ethernet 1/e1
console(config-if)# switchport access vlan 1
VLAN routing
console#config
console(config)#ip routing
console(config)#interface vlan 2
console(config-if-vlan2)#routing
console(config-if-vlan2)#exit
Creating Static Routes
console> enable
console# config
console(config)# ip route 172.16.0.0 255.255.0.0 10.0.0.2
console(config)# end
console#
Configure LLDP – Marvell-based Switch
console> enable
console# config
console(config)# interface range ethernet 1/e5-10
console(config-if)# lldp optional-tlv port-desc sys-name sys-desc sys-cap
console(config-if)# end
console#
Configure LLDP – 62xx Series
console>enable
console#config
console(config)#lldp notification-interval 10
console(config)#interface range ethernet 1/g1-1/g24
console(config-if)#lldp transmit-tlv port-desc sys-name sys-desc sys-cap
console(config-if)#lldp transmit-mgmt
console(config-if)#lldp notification
console(config-if)#end
console#
Configure LLDP – 8024/8024F Series (v3.1.4.5 or later)
console>enable
console#config
console(config)#lldp notification-interval 10
console(config)#interface range ethernet 1/xg1-1/xg24
console(config-if)#lldp transmit-tlv port-desc sys-name sys-desc sys-cap
console(config-if)#lldp transmit-mgmt
console(config-if)#lldp notification
console(config-if)#end
console#
To configure Bridge priority for a Root Switch:
console# config
console(config)# spanning-tree priority 4096 ß Global config sets bridge priority
console(config)# exit
To configure Portfast on an interface:
console# config
console(config)# interface ethernet g5 ß this command will vary on different vendor platforms
console(config-if)# spanning-tree portfast ß this enables Portfast on this port
console(config-if)# exit
To reset a switch to factory defaults use the following commands:
delete startup-config or simply del start.
Reload
Snmp configuration Marvell-based switches:
console# configure
console(config)# snmp-server community public rw 172.16.0.24
console(config)# snmp-server enable traps
console(config)# snmp-server trap authentication
console(config)# snmp-server host 172.16.0.24 public
console(config)# snmp-server host 172.16.0.24 public traps 2
console(config)# snmp-server host 172.16.0.24 public informs 2
console(config)# snmp contact "John Smith"
console(config)# snmp location "First Floor"
Snmp configurationBroadcom-based switches:
console# configure
console(config)# snmp-server community public rw ip address 172.16.0.24
console(config)# snmp-server enable traps all
console(config)# snmp-server trap authentication
console(config)# snmp-server host 172.16.0.24 public traps v2
console(config)# snmp-server host 172.16.0.24 public informs
console(config)# snmp contact "John Smith"
console(config)# snmp location "First Floor"
SNTP for unicast Marvel-based switches
console(config)# clock source sntp
console(config)# clock summer-time recurring usa zone CDT
console(config)# clock timezone -6 zone CST
console(config)# sntp unicast client enable
console(config)# sntp server 10.37.112.13
SNTP for unicast Broadcom-based switches
console(config)# clock summer-time recurring usa zone CDT
console(config)# clock timezone -6 zone CST
console(config)# sntp unicast client enable
console(config)# sntp server 10.37.112.13