This post is more than 5 years old
32 Posts
0
31610
Predictive Failure reported
Hello,
Open Manage Version 7.2.0 on T420 server raid 5
I got Alert msg
Status - non Critical - "Predictive Failure reported: Physical Disk 0:1:3 Controller 0, Connector 0 "
Do I need to be worry ?
Do I need replace SAS ?
Where Can I find instruction
RARIHUT
32 Posts
1
October 14th, 2016 07:00
I didn`t try to continue.and yes It`s Dell replacement certified drive.
Drive 0:1:3 - was Failed - (20 hours after the alert msg as you said -THEFLASH1932-)
I found another Dell sas 600, and push it to cell number 5.
The server start to rebuild 0:1:5 by himself.
The server finish - (4 hours) to build 0:1:5 , then the status change to "online".
Everything looks fine!
I tried to assaing 0:1:4 as a hot-spare again , and now it works ! .
It`s look like that it was too late to try assign disk as a hot-spare.... Impossible to assign disk as hot-spare when you got physical drive alert\error .
Thank You THEFLASH1932 I really appreciate that.
RARIHUT
32 Posts
0
October 13th, 2016 07:00
Hi,
Then why it`s non Critical alert ?
I have new SAS.
How do I make the replacement ? where can I find instruction ?
Thanks
RARIHUT
32 Posts
0
October 13th, 2016 07:00
Hi,
Then why it`s non Critical alert ?
I have new SAS.
How to I make the replacement ? where can I find instruction ?
Thanks
theflash1932
9 Legend
9 Legend
•
16.3K Posts
0
October 13th, 2016 07:00
Yes, you need to make sure you have a backup and order a replacement for it ASAP.
theflash1932
9 Legend
9 Legend
•
16.3K Posts
0
October 13th, 2016 11:00
Because it is not actually failed yet. When it fails, it will say Critical.
If you have hot-swap drives, go into OMSA and use the Prepare to Remove, Replace, or Force Offline option, then pull the drive from the chassis, then insert the new one. After 1 minute, if a rebuild has not started automatically, then assign it as a hot-spare to start the rebuild. Do NOT shut down the server to replace if not-swappable.
RARIHUT
32 Posts
0
October 13th, 2016 11:00
ok
the current status
Dell idrac7
4 Physical sas identical
3 sas - Raid 5
0.1 online
0.2 online
0.3 online - problem
0.4 ready
When the server online
- make full backup
- pull out the 0.4 physical drive
- execut 0.3 - offline
- pull out the 0.3 physical drive
- insert the 0.4 drive into the problematic 0.3 place
This is the correct way to deal with that situation?
theflash1932
9 Legend
9 Legend
•
16.3K Posts
0
October 13th, 2016 12:00
Yes, but it is not necessary to move disk 4 to slot 3. Can if you want, but it is not necessary.
RARIHUT
32 Posts
0
October 13th, 2016 13:00
automatically disk 4 will enter to rebuild/online mode ,
when I put disk 3 to offline mode ?
theflash1932
9 Legend
9 Legend
•
16.3K Posts
0
October 13th, 2016 13:00
Only if you assign disk 4 as a hot-spare first.
RARIHUT
32 Posts
0
October 13th, 2016 15:00
* this is my RAID 5
0:1:0 online - 600GB SAS
0:1:1 online - 600GB SAS
0:1:2 online - 600GB SAS
0:1:3 online - problem 600GB SAS
0:1:4 ready - 600GB SAS
When I tried to assign disk 4 as a hot-spare I got
caution
" Physical Disk 0:1:4: This Physical disk is not suitable to protect all current or potential virtual disks on this controller. Possible reasons include: Insufficient physical disk space, unsupported mix of SAS and SATA type physical disks, unsupported mix of SSD and HDD type physical disks, and non-SED drive assigned as a GHS when encryption virtual disk is present.
Continue with assigning as a global hot spare?
"
It`s ok to Continue ?
theflash1932
9 Legend
9 Legend
•
16.3K Posts
0
October 13th, 2016 21:00
Try it, but it probably won't rebuild. What are the makes/models of all the drives? Is the replacement a Dell certified drive?