Precision T5600 with Perc H310 controller install OS

Question

HDD with OS went bad, I replace HDD and downloaded an ISO copy from Dell to a bootable USB drive. I followed Dell’s procedure as outline for Win7 64 bit ( https://www.dell.com/support/kbdoc/en-us/000123667/how-to-download-and-use-the-dell-os-recovery-image-in-microsoft-windows ) but when I reach step (9) ( In the Where do you want to install Windows, select the largest internal disk as the Primary Partition, and then click Next) I receive no drive found. At this point I down loaded and tried to install different drives but all attempts failed.

My T5600 has Perc H310 controller card with 2 SCATA HD (800 Gb) and 1 SSD (400 Gb) which are connected ports 0, 1 and 0 (of the H310 Controller). The BIOS is set up for the H310 controller card for booting and controller card is set for Raid 1 and I’ve even tried Raid 0 with same results. My question is What am I doing wrong or not doing right? All appropriate suggestions would be appreciated

speedstep · Answer

@jgodwin21

H310 requires F6 mass storage drivers on the install media extracted to the root of the install media in order to SEE the drive.

https://www.catalog.update.microsoft.com/Search.aspx?q=DELL%20PERC%20H310

You will need to extract the drivers from the exe, zip, cab file using 7zip. You cannot point to an exe or cab or zip file. These are the files you need for PERC . CLICK THE NODEV.INF FILE to point to the perc driver

The required drivers are small but in a huge cab file

Download 7zip	.msi	64-bit x64
Download 7zip	.msi	32-bit x86

https://www.dell.com/support/kbdoc/en-us/000148150

http://www.dell.com/support/home/us/en/19/Drivers/DriversDetails?driverId=JV4JN

https://INTEL_AHCI_JV4JN_f6flpy-setup_ZPE.exe RENAME EXE TO ZIP

http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?DriverId=1DV4H&productCode=precisio...

http://DRVR_SAS_Dell_PERC8 RENAME EXE TO ZIP AND EXTRACT

HDD ports 0-4 on this board WILL activate if the PERC H310 card is removed and a device is connected to at least one of the HDD0-4 ports.

The storage controller activated appears to be the integrated Intel C600 chipset 4 port SAS/SATA controller, with PCI ID 8086:1d6b.

This chipset is documented to support SATA III speeds and TRIM but both are untested at this time.

When two or more drives are connected, the BIOS option ROM screen is enabled for "Intel(R) Rapid Storage Technology enterprise", with configuration utility available by typing Ctrl-I during boot. SCU Option ROM is version 3.2.0.1022.

When one drive is connected, the option ROM setup will not appear but the controller still functions normally.

When no drives are connected at startup, the controller will not be activated.

All ports 0-4 are activated and usable simultaneously in this configuration.

*****************************

PCI cards in General DO NOT ENUMERATE properly or install without CHIPSET DRIVERS (F6 mass Storage Drivers) Being installed FIRST.

There are 2 fiiles at the link you want the one that is 156K

http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?DriverId=1DV4H&productCode=precisio...

http://downloads.dell.com/FOLDER00575768M/9/DRVR_SAS_Dell_PERC8-1DV4H_Win7_X64_WHQL_setup_ZPE.exe

'"Windows Setup could not configure Windows on this computer’s hardware" installation error on a Win....

This is not cookie cutter you must extract the drivers and point to them on a USB storage device unzipped. EXE OR ZIP is not F6 READABLE.

Go to another computer that has an internet connection and click the link below to download the PERC driver for your hard disk drive (either 32-bit or 64-bit):
Save the downloaded driver to a DVD or USB flash drive or an external hard drive that can be taken to the PC that you're installing Windows to. Its an exe rename it .zip and extract the 4 files.
Next, start the installation of Windows 7 or Windows Server 2008 R2 and watch for the Load Driver option. You will see this option on the Where do you want to install Windows? screen in the lower right corner.
Connect the USB flash or external drive to the computerthat you're installing Windows or take the Windows DVD out of the drive and put the driver DVD into the drive. (You will put the Windows DVD back into that drive after the driver is loaded)
Click Load Driver, (clicking this option checks removable media for storage controller drivers)
Once the driver is loaded, continue with the Windows setup.

The Advanced Drive Format hard drive will be recognized and Setup will continue as expected.

http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?DriverId=1DV4H&productCode=precisio...

http://DRVR_SAS_Dell_PERC8-1DV4H_Win7_X64_WHQL_setup_ZPE.exe

Rename this EXE to PERC.ZIP

then extract the 4 FILES to diskette or USB flash drive with 7zip extract here and F6 point to them. In windows 7 you "load drivers" from usb flash drive.

DELL HV52W

Dell Spare Part Number (PN): HV52W.

Long Description: PERC8 SAS H310, Full Height
Short Description: PWA,CTL,SAS,H310,ADPT,FH,PWS

The Dell Driver package says:

Title: SAS RAID: PERC H310/H710P Adapter for Precision Workstations,

==========================
Supported RAID Controllers
==========================
This download supports the following controllers

LSI MegaRAID: MegaRAID SAS 9240-4i/8i,MegaRAID SAS 9260-4i/8i/16i,MegaRAID SAS 9261-8i,MegaRAID SAS 9280-4i4e,MegaRAID SAS 9280-8e,MegaRAID SAS 9280-16i4e,MegaRAID SAS 9280-4i4e,MegaRAID SAS 9265-8i,MegaRAID SAS 9285-8e,MegaRAID SAS 8704EM2,MegaRAID SAS 8708EM2,MegaRAID SAS 8880EM2,MegaRAID SAS 8888ELP

LSI HBA:LSI SAS3041E-R,LSI SAS3041X-R,LSI SAS3080X-R,LSI SAS3081E-R,LSI SAS3442E-R,LSI SAS3442X-R,LSI WarpDrive SLP-300,9212 4i4e-R spec,9211-8i/4i-R spec

www.dell.com/.../dell-perc-h310-spec-sheet.pdf

Precision Fixed Workstations

Precision T5600 with Perc H310 controller install OS

Was this post helpful?