Comenzar una conversación nueva

No resuelto

A

13 Mensajes

288

22 de octubre de 2019 11:00

RAID CONTROLLER NO DETECTADA MD3200i

Buenos días.

Me podrán apoyar, tengo el problema que no se detecta UNA de las controladoras RAID en ningún Slot, le conecté el cable de servicio vía putty y éste es el booteo:

-=<###>=-
Instantiating /ram as rawFs, device = 0x1
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x1
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 10000
Label:" " ...
Disk with 1024 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 1010 clusters, 3 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 6
Root dir entries 112, sysId VXDOS12 , serial number 10000
Label:" " ...
Instantiating /ram as rawFs, device = 0x1
OK.

RTC Error: Real-time clock device is not working

Adding 13884 symbols for standalone.
NVSRAM Error: Address line test failure at offset 0, expect 0x1, actual 0x11
NVSRAM Error: NVSRAM device failure. Data cannot be permanently stored.
Length: 0x13c Bytes
Version ver03.0A

System startup messages:
========================
WARN 88.32: NVSRAM Rebuild required because NVSRAM has been newly initialized
NOTE 88.30: Flash-based Config File has been modified
NOTE 88.30: NVSRAM configuration updated from flash-based Config File
NOTE 88.30: NVSRAM configuration updated from flash-based Config File

 


Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
4410 Ethernet 82574 1
01 Register read Passed
02 Register address lines Passed
6D40 Bobcat
02 Flash Test Passed
3700 PLB SRAM
01 Data lines Passed
02 Address lines Passed
7000 SE iSCSI BE2 1
01 Register Read Test Passed
02 Register Address Lines Test Passed
03 Register Data Lines Test Passed
3900 Real-Time Clock
01 RT Clock Tick ** Failed **

*** Error (0001): Real time clock failed to increment

STATUS: Real time clock failed to increment

*** Current Loop Count: 1 Date: 11/30/1999 Time: 00:00:00

*** Master Error Code: 2660-3900-01-0001


D)isplay R)etry C)ontinue M)onitor S)hell A)bort ?

3900 Real-Time Clock Skipped
Diagnostic Manager exited normally.

Controller has been locked down due to PCI errors:

Current date: 00/00/00 time: 00:00:00

Send for Service Interface or baud rate change

Ya desconecté y conecté la controladora e incluso le quité la batería interna y sigue con el mismo error.

Gracias. 

7 Technologist

 • 

1K Mensajes

28 de octubre de 2019 12:00

Hola @Ablmzk 

El problema como me lo describe apunta a un error de Hardware, ya que la misma tarjeta no está funcionando en ningún puerto PCI. Es muy probable que la controladora este dañada y necesite ser remplazada.

Si tiene otra controladora para verificar, que si funcionan en los puertos PCI para descartar la placa base, seria el siguiente paso.

Saludos

¡No se encontraron eventos!

Top