This post is more than 5 years old
2 Posts
0
1464
Map script error
Am unable to commit mapping script getting below error, how to check if any other script running background?
"Error occurred while Preparing
The configuration server can't obtain the necessary resources to perform the requested service
The configuration change session has failed."
Avinash V
91 Posts
0
July 16th, 2013 06:00
The error suggest that there is a script running on the Backend. You need to wait for the script to get completed.
Refer
https://support.emc.com/kb/73541
The Symmetrix DMX or VMAX is currently running a script. There are a variety of reasons why a script can be running on the Service Processor. Examples are listed below. However, the below list may not be exhaustive.
Avinash V
91 Posts
1
July 16th, 2013 06:00
** how to check if any other script running background?
Run the command to
symconfigure -sid XXX query
# symconfigure -h
query
Returns information about the status of a
Hope this Helps you !!
AN example .. replaced the symm sn with XXX
# symconfigure -sid XXX query
A Configuration Change query is in progress. Please wait...
A Configuration Change operation is in progress. Please wait...
Establishing a monitoring session.........................Established.
Session ID : 14146050 (0x00d7da02)
{
The session changes are in the class of: Creating new symdevices
{
create dev count=1, size=8 cyl, emulation=FBA, config=2-Way Mir,mvs_ssid=0;
}
The Application that initiated the configuration change : SYMCONFIGURE
The Host that initiated the configuration change : XXXXXX
The Process ID that initiated the configuration change : 20576
The session length : 18 secs
The session status : Running
The last action requested was: COMMIT
The state of the last action is: Running
Step 81 of 160 steps.......................................Executing.
}
Terminating the monitoring session........................Done.
The monitoring session has ended.
mrman1
2 Posts
0
July 16th, 2013 07:00
Thank you!
Fenglin1
2 Intern
2 Intern
•
2.1K Posts
0
July 16th, 2013 19:00
Hi mrman,
Sometimes there is system generated script pending in SP. You can also verify the with you SN in support.emc.com/servicecenter to see if any dial home SR exists. After waiting a while, if you still can't resume your symconfigure command. You may contact PSE for check you box.
kundu_swarup
3 Posts
0
July 18th, 2013 08:00
Hi mrman,
sometimes the configuartion script gets hung.In that case,you can see the configuration lock 15 and you would need to contact PSE lab to forcefully complete that script from backend.I faced the same error and did contact PSE lab to end the script from the backend.
KD8EWE
155 Posts
0
July 18th, 2013 08:00
Hi,
Check the following
symcfg -sid xxx list -lock -lockn all
if the output is as below or if there is any lock
XXX Local Locked 15 Config Change 1345
then
symcfg -sid XXX -lockn 15 release -force
If the above does not solve the issue ,Check who is holding the lock Anybody else running symconfigure commands from a host ??
May be you can check with symaudit and search for symconfigure actions running. Check with your local CE to see if they were the ones to set the lock. If the CE has pulled the bin for an upcoming config change they would have set the
lock to prevent any changes from occurring until the config change.
Or if the OPTIMZ is running lock can be #13, if it is and
All of the above do not release the lock then the final option.
Call EMC Support to dial in and release it
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
July 18th, 2013 09:00
i would be very carefully force releasing a lock, if a script hung in the middle of whatever it was doing you might need the PSE lab to either finish the script for your or completely roll it back.
KD8EWE
155 Posts
0
July 18th, 2013 09:00
You are correct! Dynamox.. Thanks