Microsoft Windows 32ビット形式のDell Update Package(DUP)は、Microsoft Windows 64ビットオペレーティングシステム上でも実行できるように設計されています。Microsoft Windows 64ビット形式のDell Update Package(DUP)は、Microsoft Windows 64ビットオペレーティングシステム上でのみ実行できます。デバイスドライバのアップデートを選択するときは、お使いのオペレーティングシステムに適したものを選択してください。
When installing an OS, be sure to select a Boot Device in CTRL+C. In CTRL+C, under SAS Topology, scroll down to the desired Physical Disk or Virtual Disk and enter ALT+B to select the device as your Boot Device.
- Resynch, Background Init and Consistency Check processes will always occur serially.
- When viewing SATA physical disk properties from Ctrl-C or other management applications, Vendor Identification must be translated as "ATA" followed by blanks. Please see SATA translation specification, revision 5, pages 24-25 for more details.
- When adding a PERC H200 controller to a system, either by physically adding an adapter or by enabling the integrated SAS controller in the system BIOS, the new controller may need to be added to the controller boot order in the PERC H200 BIOS configuration Utility.
- The firmware upgrade may fail if any of the RAID controllers in the system are performing an I/O background task (that is, consistency check, background initialization, rebuild, or reconstruction). Allow the background task to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect a firmware upgrade.
* Linux systems running one or more applications that interact with SCSI devices in certain ways are known to cause a kernel panic situation. Therefore, it is recommended that you stop Server Administrator and its Storage Management Service before running storage controller firmware update packages.
To stop the Dell OpenManage(TM) Server Administrator service, run "omconfig system webserver action=stop"
To start the Server Administrator service, run "omconfig system webserver action=start"
To stop the Server Administrator Storage Management Service, run "/etc/init.d/dataeng stop"
To start the Server Administrator Storage Management Service, run "/etc/init.d/dataeng start"
NOTE: This initial section of the Installation Instructions applies only to configurations with (greater than) 2TB SEDs.
1. Update the firmware version to this version using preferred method below (Zip Pack, Windows DUP, Linux DUP). 2. Reboot for the new FW take effect 3. Un-assign any (greater than) 2TB SED Dedicated or Global Hot Spares in the configuration. Not all configurations have hot spares. 4. Use CTRL-R or OMSS to issue Instant Secure Erase to all un-configured (greater than) 2TB SED drives (all data in these drives will be lost) 5. Re-assign (greater than) 2TB SED Hot Spares.
Zip pack:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your
hard drive.
Extract Files 1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package 2. Click Continue. 3. Specify the location to unzip the files. 4. Click on the OK button to extract files. After the files are extracted the message all files were successfully unzipped will appear. 5. Click the OK button to exit from the installer.
Installation 1. Copy extracted files to bootable media. 2. Reboot system to bootable media. 3. Execute update.bat to perform flash. 5. After flash is complete, remove bootable media. 4. Reboot system for changes to take effect.
Windows Update Package:
Download 1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Linux Update Package:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Read over the release information presented by executing the ./FRMW_LX_RXXXXXX.BIN --version command from the shell. 2. Download and install any prerequisites identified in the above step before proceeding. 3. Run the update by executing ./FRMW_LX_RXXXXXX.BIN from the shell. 4. Follow the remaining prompts to perform the update.
GnuPG Signature of Dell Update Package Instructions for FRMW_LX_RXXXXXX.BIN:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Import the Dell public key. (You only need to do this once on your system.) 2. Verify the Dell Update Package by using its signature file, FRMW_LX_RXXXXXX.BIN.