Data Domain – Konfigurieren physischer Schnittstellen über die Befehlszeilenschnittstelle (CLI)

Wenn Sie die Data Domain gerade an einen neuen Standort verschoben haben und alles Neue neu konfigurieren möchten, können Sie auch den Konfigurations-Setup-Befehl ausführen. 

Wenn Sie nur das Netzwerk konfigurieren möchten, überspringen Sie den Konfigurations-Setup-Befehl und verwenden Sie einfach die Net-Befehle aus diesem KB-Artikel. 

# config setup

Launch a utility program that prompts you to configure settings for the system, network, filesystem, CIFS, NFS, and licenses. Press Enter to cycle through the selections and confirm any changes when prompted. Choices include Save, Cancel, and Retry.

This command option is unavailable on Retention Lock Compliance systems. Use System Manager to change configuration settings. Role required: admin and limited-admin.

 # net config  [type {floating | fixed}]
                {[] [netmask ] | [] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu { | default}]
                [txqueuelen ]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. "Note:
                                       Change of link parameters like speed,
                                       duplex or autoneg on the DD VE is not
                                       supported."

Example # net config ethXx x.x.x.x netmask x.x.x.x 

To clear a interface give a address of zeros. 

Example # net config ethXx 0.0.0.0 

# net route set gateway { | }
                                       Set the default gateway

# net route add gateway  [interface ]
                                       Add a default gateway address,
                                       optionally to a specific interface

 # net aggregate add  interfaces 
                [mode {roundrobin |
                balanced hash {xor-L2 | xor-L3L4 | xor-L2L3} |
                lacp hash {xor-L2 | xor-L3L4 | xor-L2L3}
                [rate {fast | slow}]}]
                [up { | default}]
                [down { | default}]
                                       Add slave interfaces to an aggregate
                                       interface. Mode must be given the first
                                       time

 # net aggregate del  interfaces { | all}
                                       Delete network interfaces from an
                                       aggregate interface

 # net aggregate modify 
                [mode {roundrobin |
                balanced hash {xor-L2 |xor-L3L4| xor-L2L3} |
                lacp hash {xor-L2|xor-L3L4|xor-L2L3}
                [rate {fast | slow}]}]
                [up { | default}]
                [down { | default}]
                                       Modify the configuration of an
                                       aggregate interface. Mode must be given
                                       the first time

 # net aggregate show                   Display all aggregate interfaces

 #  net config  [type {floating | fixed}]
                {[] [netmask ] | [] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu { | default}]
                [txqueuelen ]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. "Note:
                                       Change of link parameters like speed,
                                       duplex or autoneg on the DD VE is not
                                       supported."

 # net config addresses [type {floating | fixed}]
                                       Convert IP addresses to another type.

 # net create interface { | }
                {vlan  | alias }
                                       Create a VLAN interface or an IP Alias
                                       Interface

 # net create virtual veth          Create a virtual interface

 # net destroy { |  |  }
                                       Destroy a VLAN or IP Alias or Virtual
                                       interface

 # net disable                  Disable an Ethernet interface

 # net enable                   Enable an Ethernet interface

 # net failover add  interfaces 
                [primary ]
                [up { | default}]
                [down { | default}]
                                       Add network interfaces to a failover
                                       interface

 # net failover del  interfaces { | all}
                                       Delete network interfaces from a
                                       failover interface

 # net failover modify  [primary { | none}]
                [up { | default}]
                [down { | default}]
                                       Modify the primary network interface
                                       for a failover interface

 # net failover show                    Display all failover interfaces

 # net modify  bonding {aggregate | failover}
                                       Change the bond mode between failover
                                       and aggregate

 # net ping { | |  [ipversion {ipv4 | ipv6}]}
                [broadcast] [count ] [interface ]
                [packet-size ] [path-mtu {do | dont | want}]
                [pattern ] [numeric] [verbose]
                                       Ping a host. Param 'broadcast' is for

 # net show all                         Display all networking information

 # net show config []           Display the configuration for the
                                                             Ethernet interface

 # net show hardware                    Display Ethernet port information

 # net show hostname [type {local|ha-system}]
                                       Display the hostname

 # net show settings                    Display Ethernet interface settings

 # net show stats [[ipversion {ipv4 | ipv6}] [all | listening] [detailed] |
                [ipversion {ipv4 | ipv6}] route | interfaces |
                [ipversion {ipv4 | ipv6}] statistics]
                                       Display network statistics

 # net troubleshooting duplicate-ip     Detect duplicate IP in network