Dell Unity: Não é possível criar pool tradicional a partir do Unisphere OU RAID 5 ou 10 não disponível ao criar pool a partir do Unisphere
Summary: Não é possível criar pool tradicional a partir da interface do usuário do Unity OU RAID 5 ou 10 não disponível ao criar pool a partir da interface do usuário do Unity. (Corrigível pelo usuário) ...
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Symptoms
Nessa situação, o array do Unity estava executando o OE 5.2 e todas as unidades NL-SAS estavam presentes no array.
Ao tentar criar um pool a partir do Unisphere, somente o RAID 6 está disponível (RAID 5 e RAID 10 não estão disponíveis).
Ao tentar criar um pool a partir do Unisphere, somente o RAID 6 está disponível (RAID 5 e RAID 10 não estão disponíveis).
Cause
O array do Unity está funcionando conforme projetado.
No Dell Unity OE versão 4.2 e posteriores, um pool dinâmico é o único tipo de pool que pode ser criado no Unisphere para um sistema All-Flash. Além disso, isso é verdadeiro para sistemas híbridos que executam o OE versão 5.2 e posterior. A criação de um pool tradicional requer o uso da CLI ou da API REST do Unisphere. Além disso, ao criar um pool dinâmico com unidades NL-SAS, somente o RAID 6 é permitido ao usar o Unisphere.
Para obter mais informações, consulte:
No Dell Unity OE versão 4.2 e posteriores, um pool dinâmico é o único tipo de pool que pode ser criado no Unisphere para um sistema All-Flash. Além disso, isso é verdadeiro para sistemas híbridos que executam o OE versão 5.2 e posterior. A criação de um pool tradicional requer o uso da CLI ou da API REST do Unisphere. Além disso, ao criar um pool dinâmico com unidades NL-SAS, somente o RAID 6 é permitido ao usar o Unisphere.
Para obter mais informações, consulte:
Resolution
Um pool tradicional pode ser criado a partir da CLI usando os comandos abaixo
1) uemcli /stor/config/profile -traditional -configurable show <- Shows the profiles available in the system ID = tprofile_2 Type = Traditional Description = SAS Flash RAID5 (8+1) Drive type = SAS Flash RAID level = 5 Maximum capacity = 18510768046080 (16.8T) Stripe length = 9 Disk group = dg_26 Maximum drives to configure = 45 Maximum capacity to configure = 14834210439168 (13.4T)
2) uemcli /stor/config/dg show <- Shows the Disk Groups available in the system ID = dg_26 Drive type = SAS Flash 3 FAST Cache = no Drive size = 393846128640 (366.7G) Vendor size = 400.0G Rotational speed = 0 rpm Number of drives = 47 Unconfigured drives = 47 Capacity = 18510768046080 (16.8T) Recommended number of spares = 0
3) uemcli -d <IP Address> -u Local/admin -p <Password> /stor/config/pool create -name <Pool Name> -diskGroup dg_26 -drivesNumber 45 -storProfile tprofile_2 -type traditional <- Command to create a traditional Pool (we use 45 of the 47 drives to leave 2 for spares) Note: This command is run from a workstation with Unity uemcli installed. Alternately the command can be run directly on the SP via an SSH connection: uemcli -u Local/admin -p <Password> /stor/config/pool create -name <Pool Name> -diskGroup dg_26 -drivesNumber 45 -storProfile tprofile_2 -type traditional
Affected Products
Dell EMC Unity, Dell Unity 300, Dell EMC Unity 300F, Dell EMC Unity 350F, Dell EMC Unity XT 380, Dell EMC Unity 400, Dell EMC Unity 400F, Dell EMC Unity 450F, Dell EMC Unity 500, Dell EMC Unity 500F, Dell EMC Unity 550F, Dell EMC Unity 600
, Dell EMC Unity 600F, Dell EMC Unity 650F, Dell EMC Unity Family |Dell EMC Unity All Flash, Dell EMC Unity Family, Dell EMC Unity Hybrid
...
Article Properties
Article Number: 000201423
Article Type: Solution
Last Modified: 20 Dec 2024
Version: 8
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.