Siirry pääsisältöön
Kirjaudu ulos

Tervetuloa Dellin asiakkaaksi

Oma tili
  • Tee tilauksia nopeasti ja helposti
  • Tarkastele tilauksia ja seuraa lähetyksen tilaa
  • Luo tuoteluettelo ja käytä sitä
  • Hallitse Dell EMC-sivustoja, tuotteita ja tuote-tason yhteystietoja yrityksen hallinnan avulla.
Kirjaudu sisään Luo tili Premier-kirjautuminen Kumppaniohjelman sisäänkirjautumissivu
Ota yhteyttä

Artikkelin numero: 000134054

Latitude 3410 Teardown, removal guide for customer replaceable units (CRUs)

Yhteenveto: A guide to safe removal and replacement of those parts of a Latitude 3410 notebook that Dell considers safe and easy for anyone to attempt

Tämä artikkeli on saatettu kääntää automaattisesti. Jos sinulla on palautetta sen laadusta, ilmoita siitä meille käyttämällä tämän sivun alareunassa olevaa lomaketta.

Artikkelin sisältö

Oireet

These guides take you step-by-step through the safe removal of the Customer Replaceable Unit (CRU) parts of a Latitude 3410 Notebook system. (CRUs are the parts of the system that should not need an engineer to remove or replace.) The guides will include pictures to reference what is involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

Syy

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you want to reference your System Manual.

The article below provides information about safe practices to consider before working with electrical equipment.


Back to Top

Tarkkuus

 

Removal Instructions

 

SLN321332_en_US__1icon Note: Click the title of the section you want to open below, in order to see the contents.
 
|

 

SLN321332_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
SLN321332_en_US__1icon Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools, that are not available to our onsite engineers.

 

  1. Pre-Removal Instructions before removing the Access Panel:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Turn the system over on it is closed lid and loosen the eight (8) captive screws. The screws are around the edge of the system and secure the access panel to the chassis

SLN321332_en_US__4CRU_3410_Door_01_BK

  1. Using a plastic scribe or some other tool that will not mark the plastics, pry the cover up from the right-hand side hinge. Work clockwise around the access panel to release it from the chassis

SLN321332_en_US__5CRU_3410_Door_02_BK

  1. Lift the panel up and away from the chassis

 

  1. Pre-Removal Instructions before removing the Memory:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and disconnect the battery cable

  2. With the system placed on its closed lid, the memory is located in the top right-hand side corner of the system

SLN321332_en_US__6CRU_3410_Memory_01_BK

  1. Pull apart the metal clips holding the DIMM in place

SLN321332_en_US__7CRU_3410_Memory_02_BK

  1. When the DIMM lifts up at an angle to the base, pull it out of the socket and away from the system

SLN321332_en_US__1icon Note: Repeat the steps 3 and 4 for any additional memory DIMMs located in the system.

 

  1. Pre-Removal Instructions before removing the Solid State Drive (SSD):

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and disconnect the battery cable

  2. With the system on its closed lid, the SSD is located in under the system fan on the left-hand side corner of the system.

For the M.2 2280 SSD:

  1. Remove the single (1) screw that secures the M.2 2280 SSD to the chassis and the card will spring up at an angle to the motherboard

SLN321332_en_US__9CRU_3410_SSD_01_BK

  1. Maneuver the SSD card out of the SSD connector and away from the system

For the M.2 2230 SSD:

  1. Remove the single (1) screw that secures the M.2 2230 SSD to the chassis and the card will spring up at an angle to the motherboard

SLN321332_en_US__10CRU_3410_SSD_03_BK

  1. Maneuver the SSD card out of the SSD connector and away from the system

 

  1. Pre-Removal Instructions before removing the Coin Cell Battery:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and disconnect the battery cable

  2. With the system on its closed lid, the coin cell battery is located under the SSD card in left-hand side of the system. Disconnect the coin cell battery cable from the motherboard

SLN321332_en_US__11CRU_3410_CoinCell_01_BK

  1. Lift the coin cell battery away from the adhesive on the motherboard

 

  1. Pre-Removal Instructions before removing the Micro-SD Memory Card:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. The Micro SD slot is located on the right-hand edge of the system. Push in gently on the card in the slot and release to have it pop out of the slot [1]

SLN321332_en_US__12CRU_3410_MSD_BK

  1. Grip the card and pull it the rest of the way out of the slot [2]

 

  1. Pre-Removal Instructions before removing the WLAN Card (WiFi, Wireless):

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and unplug the battery cable

  2. With the system on it is closed lid, the WLAN card is located in the center of the system

  3. Remove the single (1) screw that secures the WLAN card bracket to the chassis

SLN321332_en_US__13CRU_3410_WLAN_01_BK

  1. Remove the bracket from on top of the antenna cables and the card will pop up at an angle from the motherboard

  2. Disconnect the antenna cables pop connectors from the press studs on the WLAN card

SLN321332_en_US__14CRU_3410_WLAN_02_BK

  1. Pull the card out of the connector on the motherboard and away from the system

 

If you require further assistance, please contact Technical Support.

 

  Contact Us  

Artikkelin ominaisuudet

Tuote, johon asia vaikuttaa

Latitude 3410

Edellinen julkaisupäivä

28 syysk. 2023

Versio

5

Artikkelin tyyppi

Solution

Takaisin ylös