Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Dell Command Line Reference Guide for the S6010–ON System 9.14.2.4

PDF

arp

To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP).

Syntax
arp [vrf vrf-name] ip-address mac-address interface

To remove an ARP address, use the no arp ip-address command.

Parameters
vrf vrf-name
Enter a VRF name to configure an ARP entry for that VRF. Use the VRF option after the keyword arp to configure a static arp on that particular VRF.
ip-address
Enter an IP address in dotted decimal format.
mac-address
Enter a MAC address in nnnn.nnnn.nnnn format.
interface
Enter any of the following keywords and the interface information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
Defaults
Not configured.
Command Modes
CONFIGURATION
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100–ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100–ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.4(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.5.1.0
Added support for 4-port 40G line cards on the E-Series.
8.3.7.0
Introduced on the S4810.
8.1.1.0
Introduced on the E-Series.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
pre-6.2.1.0
Introduced on the E-Series.
Usage Information

You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid.

You can use the vrf attribute of this command to create a static ARP entry on either a default or a non-default VRF. You cannot use this parameter to create any static ARPs corresponding to management VRFs. When a VRF is deleted using the no ip vrf command, all the static ARP configurations that belong to that VRF are removed automatically.

Although static ARP entries take precedence over dynamically-learnt ARP entries, a static ARP entry that points to a wrong port is not included in the FIB or ARP entries.

Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\