Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Configuring the Control VLAN

Control and member VLANS are configured normally for Layer 2. Their status as control or member is determined at the FRRP group commands.

For more information about configuring VLANS in Layer 2 mode, refer to Layer 2.
Be sure to follow these guidelines:
  • All VLANS must be in Layer 2 mode.
  • You can only add ring nodes to the VLAN.
  • A control VLAN can belong to one FRRP group only.
  • Tag control VLAN ports.
  • All ports on the ring must use the same VLAN ID for the control VLAN.
  • You cannot configure a VLAN as both a control VLAN and member VLAN on the same ring.
  • Only two interfaces can be members of a control VLAN (the Master Primary and Secondary ports).
  • Member VLANs across multiple rings are not supported in Master nodes.

To create the control VLAN for this FRRP group, use the following commands on the switch that is to act as the Master node.

  1. Create a VLAN with this ID number. CONFIGURATION mode. interface vlan vlan-id VLAN ID: from 1 to 4094.
  2. Tag the specified interface or range of interfaces to this VLAN. CONFIG-INT-VLAN mode. tagged interface slot/ port { range}
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port.
  3. Assign the Primary and Secondary ports and the control VLAN for the ports on the ring. CONFIG-FRRP mode. interface primary int slot/port secondary int slot/port control-vlan vlan id
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port. VLAN ID : The VLAN identification of the control VLAN.
  4. Configure the Master node. CONFIG-FRRP mode. mode master
  5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id { range} VLAN-ID, Range : VLAN IDs for the ring’s member VLANS.
  6. Enable FRRP. CONFIG-FRRP mode. no disable

Califique este contenido

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
0/3000 characters
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Seleccione si el artículo fue útil o no.
  Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"