- Notes, cautions, and warnings
- Dell PowerEdge C4130 overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- System covers
- Inside the system - PowerEdge C4130
- Chassis intrusion switch
- IDSDM
- Cooling shroud
- Processor blank
- System memory
- Processors and heat sinks
- System battery
- PCIe shroud
- Expansion card riser and expansion cards
- Power supply units
- Hard drives
- Removing the optional 2.5 inch hard drive cage
- Installing the optional 2.5 inch hard drive cage
- Removing the optional 2.5 inch hard drive cage cover
- Installing the optional 2.5 inch hard drive cage cover
- Removing 2.5 inch cabled hard drives from the hard drive cage
- Installing a 2.5 inch cabled hard drive into the hard drive cage
- Hard drive cabling diagrams
- uSATA SSDs
- Removing a 1.8 inch uSATA SSD blank
- Installing a 1.8 inch uSATA SSD blank
- Removing a 1.8 inch uSATA SSD carrier
- Installing a 1.8 inch uSATA SSD carrier
- Removing a 1.8 inch uSATA SSD from a SSD carrier
- Installing a 1.8 inch uSATA SSD into a SSD carrier
- Removing the 1.8 inch uSATA SSD cage
- Installing the 1.8 inch uSATA SSD cage
- Removing the 1.8 inch uSATA SSD backplane
- Installing the 1.8 inch uSATA SSD backplane
- Internal USB memory key (optional)
- Cable routing clip
- System board
- Trusted Platform Module
- Cooling fans
- Graphics processing unit
- PCIe Graphics processing unit
- GPU installation guidelines
- Removing a GPU blank
- Removing a GPU riser cable from the system board
- Removing a GPU
- Removing a GPU riser cable board
- Removing the custom GPU brackets from the GPUs removed from your system
- Removing the GPU brackets from the replacement GPUs
- Removing the optional GPU switch board
- Installing the optional GPU switch board
- Installing the GPU brackets on the GPUs removed from your system
- Installing the custom GPU brackets on the replacement GPUs
- Installing a GPU riser cable board
- Installing a GPU blank
- Installing a GPU
- Installing a GPU riser cable on the system board
- GPU cabling diagrams
- SXM2 Graphics processing unit
- Control panel module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Troubleshooting a GPU
- System messages
- Getting help
Dell PowerEdge C4130 Owner's Manual
System messages
For information about the event and error messages generated by the system firmware and agents that monitor system components, see the Error Code Lookup page at qrl.dell.com
Proporcione calificaciones (1 a 5 estrellas).
Proporcione calificaciones (1 a 5 estrellas).
Proporcione calificaciones (1 a 5 estrellas).
Seleccione si el artículo fue útil o no.
Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"