You can use the Integrated Devices screen to view and configure the settings of all integrated devices
including the video controller, integrated RAID controller, and the
USB ports.
About this task
You can view
the Integrated Devices screen by clicking System Setup Main Menu > System BIOS > Integrated Devices.
The Integrated Devices screen details are
explained below.
Menu Item
Description
User Accessible USB Ports
Enables or disables the USB ports. Selecting Only Back Ports On disables the front USB ports, selecting All Ports Off disables all USB ports, selecting All Ports Off (Dynamic) disables all USB ports during
P.O.S.T. The USB keyboard and mouse operates during boot process in
certain operating systems. After the boot process is complete, the
USB keyboard and mouse do not work if the ports are disabled.
NOTE:Selecting Only Back Ports On and All Ports Off will disable the USB management port and also restrict access to
iDRAC features.
Internal USB Port
Enables or disables the internal USB port. By default,
the option is set to On.
iDRAC Direct USB Port
iDRAC Direct USB Port managed by iDRAC exclusively
with no host visibility. When set to off iDRAC would not detect any
USB device installed. Option is set to On
Integrated Network Card 1
Enables or disables the integrated network card.
I/OAT DMA Engine
Enables or disables the I/OAT option. Enable only
if the hardware and software support the feature.
Embedded Video Controller
Enables or disables the Current state
of Embedded Video Controller . By default the option Disabled. Current State of Embedded Video
Controller is a read only field, indicating the current
state for the Embedded Video Controller. If the Embedded Video Controller
is the only display capability in the system (that is, no add-in graphics
card is installed), then the Embedded Video Controller is automatically
used as the primary display even if the Embedded Video Controller
setting is Disabled.
NOTE:1. If the embedded
video controller is DISABLED in BIOS and if
you launch the Virtual Console from the iDRAC, the Virtual Console
Viewer is blank.
NOTE:2. All monitors must
be plugged into the GPU at power on, and must remain plugged into
the GPU until the system is booted into the operating system with
the driver loaded. Once the system is booted into the operating system
the monitor can be unplugged, and then hot plugged. The monitor will
not be hot pluggable unless this process is followed.
DP cable can be hot plugged
mDP cable can be hot plugged
DVI cable can be hot plugged
DP to VGA dongle cable cannot be hot plugged
Current State of Embedded Video Controller
Displays the current state of the Embedded
Video Controller. Current State of Embedded
Video Controller is a read only field, indicating the
current state for the Embedded Video Controller
SR-IOV Global Enable
Enables or disables the BIOS configuration of Single
Root I/O Virtualization (SR-IOV) devices. By default, the SR-IOV Global Enable option is set to Disabled.
OS Watchdog Timer
If your system stops responding, this watchdog timer
aids in the recovery of your operating system. When this field is
set to Enabled, the operating system is allowed
to initialize the timer. When the option is set to Disabled (the default), the timer will have no effect on the system.
Memory Mapped I/O above 4GB
Enables or disables the support for PCIe devices
that require large amounts of memory. By default, the option is set
to Enabled.
Lower Memory Mapped I/O base to 512GB
When set to enabled system will map MMIO base to
512 GB and reduce the maximum support for memory to less than 512
GB.
Slot Disablement
Enables or disables the available PCIe slots on your
system. The Slot Disablement feature controls
the configuration of PCIe cards installed in the specified slot. Slot
disablement must be used only when the installed peripheral card is
preventing booting into the operating system or causing delays in
system startup. If the slot is disabled, both the Option ROM and UEFI
driver are disabled.
This field controls the configuration
of the card installed in the slot. You can set one of the following
options for each of the .....(Press F1 for more information)