- Notes, cautions, and warnings
- PowerEdge FC430 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- System memory
- PCIe mezzanine card
- Internal Dual SD Module (IDSDM) card
- SD vFlash card
- LAN on Motherboard (LOM) riser card
- Processors
- Processor blank and DIMM blank
- Solid State Drives (SSD)
- Solid State Drive (SSD) backplane
- System battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Willkommen
Dell Standorte
Dell Standorte
Willkommen bei Dell
Mein Konto
- Bestellungen schnell und einfach aufgeben
- Bestellungen anzeigen und den Versandstatus verfolgen
- Erstellen Sie eine Liste Ihrer Produkte, auf die Sie jederzeit zugreifen können.
- Verwalten Sie mit der Unternehmensverwaltung Ihre Dell EMC Seiten, Produkte und produktspezifischen Kontakte.
Dell PowerEdge FC430 Owner's Manual
Removing the PCIe mezzanine card
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized
in your product documentation, or as directed by the online or telephone
service and support team. Damage due to servicing that is not authorized
by Dell is not covered by your warranty. Read and follow the safety
instructions that are shipped with your product.
- Follow the safety guidelines listed in the Safety instructions section.
Follow the procedure listed in the Before working inside your system section.
If connected, disconnect all external storage devices.
If connected, disconnect all USB devices.
Remove the SSD cage.
Keep the Phillips #2 screwdriver ready.
Steps
- To remove the SSD cage base cover:
- Place the SSD cage upside down with the USB ports to your right.
- Remove the screws securing the SSD cage base cover to the SSD cage.
- Slide the SSD cage base cover back and lift the cover away from the SSD cage.
Figure 1. Removal of the SSD cage base cover 
- SSD cage
- screw (2)
- SSD cage base cover
- To remove the PCIe mezzanine card:
- Remove the screws securing the PCIe mezzanine card to the SSD cage.
- Slide the mezzanine card back and lift the card away from the SSD cage.
- Remove the PCIe mezzanine card bridge and keep it aside for future use.
CAUTION: To prevent damage to the PCIe mezzanine card, you must hold the card only by its edges.Figure 2. Removing a PCIe mezzanine card 
- screw hole on SSD cage (2)
- external storage connector (2)
- PCIe mezzanine bridge card
- Screw (2)
- PCIe mezzanine card
- SSD cage
Next steps
Install the PCIe mezzanine card.
Install the SSD cage.
If applicable, reconnect the disconnected storage devices.
If applicable, reconnect the disconnected USB devices.
Follow the procedure listed in the After working inside your system section.
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie an, ob der Artikel hilfreich war.
Die folgenden Sonderzeichen dürfen in Kommentaren nicht verwendet werden: <>()\