- Notes, cautions, and warnings
- Dell PowerEdge T630 server overview
- Converting the system from tower mode to rack mode
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions for converting system from tower to rack
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System feet
- Caster wheels – optional
- System cover
- Inside the system
- Cooling shroud
- Cooling fans
- Cooling-fan assembly (optional)
- System memory
- Flex bays
- Hard drives
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter
- Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter
- Installing a 3.5-inch hard drive adapter into a hot swap hard drive carrier
- Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Optical drives and tape drives
- Internal USB memory key (optional)
- Expansion card holder
- Expansion cards
- GPU card holder (optional)
- GPU cards (optional)
- Internal dual SD module (optional)
- Internal SD card
- Processors and heat sinks
- Power supply unit
- System battery
- Hard drive backplane
- SD vFlash card (optional)
- Control panel assembly
- System board
- Trusted Platform Module
- Power interposer board and power distribution board
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Bienvenue
Bienvenue dans l’univers Dell
Mon compte
- Passer des commandes rapidement et facilement
- Afficher les commandes et suivre l’état de votre expédition
- Créez et accédez à une liste de vos produits
- Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Dell PowerEdge T630 Owner's Manual
Installing the power interposer board
Prerequisites
CAUTION: Many repairs may only
be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation,
or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that are
shipped with your product.
Follow the safety guidelines listed in the safety instructions section.
Steps
- Install the power distribution board (PDB).
- Align the power interposer board (PIB) connector with the connector on the PDB.
- Align the grooves on the PIB aligned with the pins on the chassis, and then connect the PIB to the connector on the PDB.
Next steps
- Install the system board. For more information, see the Installing system board section.
- Connect the power cables to the system board and the hard-drive backplane.
- If applicable, install the cooling fan assembly.
- Install the cooling shroud.
- Install the PCIe card holders.
- Install the power supply module(s) in their original locations.
- Follow the procedure listed in the After working inside your system section.
- power interposer board
- power distribution board
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez attribuer une note (1 à 5 étoiles).
Veuillez indiquer si l’article a été utile ou non.
Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\