Search

Posts

Search Results (1.6K)

Conversation Type :

Posts

Published Date :

Lifetime

Category

Most Recent

Community Accepted Solution

VRRP on OS10 static VXLAN

We are building some static VXLANs on OS10 10.5.4.201 with 5248s and 5224s. The docs only mention Anycast as the protocol for virtual IPs for clients to use as default gateways. Apparently anycast can also be used for plain old SVIs as well as VRRP. Anyone know if the reverse is also true? Could we

Question

69

4

0

Community Accepted Solution

STP message

Hello all, Every 15min and sometimes every half an hour I get this message in my log file of N2048 series switch. <189> Nov 20 14:47:52 d3sw1-1 TRAPMGR[dot1s_task]: traputil.c(795) 84096054 %% NOTE Spanning Tree Topology Change Received: MSTID: 0 Gi1/0/48<189> Nov 20 14:47:50 d3sw1-1

Question

87

2

0

Community Accepted Solution

N3208PX-ON SFP 1GB Support

from the 3200 series specification sheet, the N3208PX-ON is indicated as having 2x10G SFP+ ports. despite what is written in the specification sheet, can the N3208PX-ON support 1G speeds on its SFP+ ports ? Thank you.

Question

65

4

0

Community Accepted Solution

VLAN interface in VLT

I have a pair of 4148 switches configured with VLT. I have VLAN 100 configured with an interface on both switches with the same IP address. This VLAN is specifically to be used for inter-switch communication to our edge switches via a port on each 4148 in a VLT-port-channel configuration. Edge switc

Question

179

2

0

Community Accepted Solution

Error from configuring Port Monitoring on switch - Destination port should not be a L2/L3 port

I'm currently working with Dell OS10 switches. The problem is very simple:I tried to configure port-mirroring, to clone the packet to another port which locates in same switch. I attempted to execute commands below, however, I faced an error and got stuck. OS10(config)# monitor session 1OS10(conf-m

Question

210

3

0

Community Accepted Solution

Changing Access Vlan via PYSNMP

I would like to change 'switchport access vlan <>' configuration via PYSNMP library. For example, I would like change the configuration 'switchport access vlan 202' to 'switchport access vlan 201' via SNMP. The interface is in 'switchport mode access' mode. VLAN membership mode..............

Question

38

2

0

Community Accepted Solution

Dell S4048 (OS9) iSCSI Optimization for PowerVault ME4024

I've been reading through the iSCSI optimization docs for the S4048 running OS9. I see that it mentions "EqualLogic" and "Compellant" storage arrays. Dell no longer sells products under those names. I am wondering if following the manual iSCSI optimization as outlined here for Compellant arrays will

Question

56

4

0

Community Accepted Solution

Dell S5232F-ON cannot see link to Cisco Nexus C93180YC-FX3 - No logs or negotiations

Hello, Thanks for reading and possibly support the case. Trying to get an uplink to the Dell S5232 from my Nexus core, but the dell ports just dont come up. Here is the config of my dell port: show interface ethernet 1/1/32Ethernet 1/1/32 is up, line protocol is downHardware is Eth, address is c4:

Question

260

5

0

Community Accepted Solution

Network card not visible in OS

I'm trying to install a Dell BCM5720 Dual Port in a Dell PowerEdge R730XD The card is detected in the BIOS and also in iDRAC as BRCM GbE 2P 5720-t Adapter Instead, when I boot to linux or windows I can only see the integrated network card Even if I try to execute the command hwinfo --netcard there

Question

864

21

0

Community Accepted Solution

Adding 10G Base-T module to N4064F

Hi, We have a plan to add a 10G Base-T module to N4064F. Do we need to shutdown the switch for adding this module? One more question, My colleague said this module is used for only stacking. Is it true? I believe we can use it for an ethernet port too.   Thanks,

Question

100

2

0

Community Accepted Solution

VLT issues DELL S4112F / DELL N1524 (+ others)

Hi! I have a few DELL switches setup as VLT domains in the environment I’m managing.  I recently got 2 new S4112F switches and set them up exactly as I have done before with a new VLT domain.  I got one “4-port portchannel” (2 ports in each switch) going to another VLT domain and that is

Question

284

4

0

Community Accepted Solution

Closed

RSTP switches reporting they're in different regions

In a network I've had to inventory recently I found an interesting fact which I couldn't explain. There were 2 switches, both configured for RSTP, yet both were convinced they were in different regions.The switches are a HPE 5710 48XGT 6QS+/2QS28 and a Dell N1108T-ON. There weren't any other STP awa

Question

146

4

0

0

Community Accepted Solution

Closed

Inter Vlan routing

Hi there, I am working with Dell EMC N3248TE-ON. I got three vlans. Each have IP address assigned. Routing mode is enabled. I have two Esxi hosts connected to trunk ports on the dell switch.  Devices are able to reach vlan ip addresses with ping. Devices are not able to reach devices in

Question

555

1

0

0

Community Accepted Solution

Closed

Dell S4048-On

Good morning! We have a switch Dell 4048: #sh verDell EMC Real Time Operating System SoftwareDell EMC Operating System Version: 2.0Dell EMC Application Software Version: 9.14(2.16)Copyright (c) 1999-2021 by Dell Inc. or its subsidiaries. All Rights Reserved.Build Time: Mon Aug 1 08:17:19 2022Build

Question

152

2

0

0

Community Accepted Solution

Closed

S5248F can not Config vlt-port-channel xx % Error: Internal error

We need to config interface port-channel114 to S5248F = 2 Units with VLT for example interface port-channel114switchport mode trunkvlt-port-channel 114 But put the command then show error Dell-SW01(conf-if-po-114)# vlt-port-channel 104% Error: Internal error   Please help me get the

Question

254

2

0

0

Community Accepted Solution

Closed

What is the point of switch port profiles?

I just inherited an environment that has a couple of Dell 4148T-ON switches and I noticed that bunch of ports were "missing" and after some digging I found switch-port-profiles which I think are hardcoded port configurations. I have a couple of questions: 1) What is the point of choosing one of th

Question

223

2

0

0

Community Accepted Solution

Closed

Switch S4112T with 12x 10GBASE-T RJ-45 ports - Maximum distance with CAT7

The 10GBase-T RJ45 port max distance with CAT7 cable should be 100 meters. On DELL S4112T we have 12 ports 10GBase-T RJ45, can we connect a device at 100 meters and may expect 10Gb link?

Question

304

3

0

0

Community Accepted Solution

Closed

dell powerconnect 5548P "LAG speed cannot be higher than its capacity"

        Hi,      We created some LAGs for Synology NAS devices merging 3 links on each, it's up and working but bandwith is not reaching 3GB as expected (the NAS side link is running at 2,5GB localy). I tried to force 10GB it's not working and i'm ok with that (L

Question

227

1

0

0

Community Accepted Solution

Closed

reset admin password for S4128T-ON

Hello, I need to reset the admin password for dell Switch S4128T-ON, I have try the instructions on this guide but not working for me. https://dl.dell.com/topics/pdf/force10-s4048-on_reference-guide7_en-us.pdf after  modifying the boot it gives me the below errors and can't complete the steps Loadin

Question

900

3

0

0

Community Accepted Solution

Closed

N1108EP-ON vs N1108T-ON

Hello Could you please let me know what is the difference between N1108EP-ON and N1108T-ON? Many thanks

Question

194

2

0

0

Dell Support Results

No Results found!

Top