2. Once precopy is at 100%, split R1 and R2 ( I guess this step is not required)
3. Activate clone session. ==> Activating the clone session will normally make your target clone device as RW and host can access the target clone LUN. Why we need step 4?
4. Once session status is copied, next step clone session split. ==> Your clone session should be in restored state if you want to perform Split. You can't split the clone session when it is in copied state.
"Set "auto_link_recovery" not supported on prior to Enginuity 5875."
ID:
emc260979
Usage:
1
Date Created:
01/28/2011
Last Modified:
07/21/2011
STATUS:
Approved
Audience:
Customer
Knowledgebase Solution
Environment:
EMC SW: EMC Solutions Enabler 7.2
Environment:
Enginuity: 5874
Environment:
EMC SW: EMC Solutions Enabler SYMCLI 7.2
Problem:
Cannot set parameter "auto_link_recovery" on.
Problem:
symrdf -sid 277 -rdfg 199 set auto_link_recovery on -both_sides
Problem:
The requested feature is not supported for this microcode or SYMAPI version
Change:
Trying to set "auto_link_recovery" parameter ON on dynamic RDF pair.
Fix:
Automatic Recovery mode is RDF group-level attribute. The feature ensures devices that were ready to their host before a link failure are automatically restored to a ready state once the link is up and running.
This is a new option which is available from micro code version 5875 and above and not in 5874, but in the document its not
sauravrohilla
859 Posts
0
August 1st, 2012 01:00
Hi Yere,
Hope you are doing well. do you have R1 or R2 local invalids? Did you use -precopy option while creating the session?
regards,
Saurabh
ybraju_unb
14 Posts
0
August 1st, 2012 04:00
Hey Saurabh,
Thanks I am doing good, how are you.
We don't have invalids, but clone session is created with precopy option
as mentioned. Client is using script below are the steps in the script.
1. Create clone session with precopy.
2. Once precopy is at 100%, split R1 and R2 ( I guess this step is
not required)
3. Activate clone session.
4. Once session status is copied, next step clone session split.
As per the script it was happened all these days, only from yesterday we
are facing this issue. I tried the same procedure manually without
script, but unable to split
Thanks & Regards ,
Basavaraju Y
Storage Administrator
Information Technology Group
Phone: 02-6984174 - ext: 1174
0_Specialist
ybraju_unb
14 Posts
0
August 1st, 2012 04:00
No.
Thanks & Regards ,
Basavaraju Y
Storage Administrator
Information Technology Group
Phone: 02-6984174 - ext: 1174
0_Specialist
sauravrohilla
859 Posts
0
August 1st, 2012 04:00
Is there a failed disk?
sauravrohilla
859 Posts
0
August 1st, 2012 04:00
ok, paste the TF query and SRDF query output. If possible, capture the debug while spliting the clone and send it to me. Send it to my gmail
regards,
Saurabh
ybraju_unb
14 Posts
0
August 27th, 2012 01:00
Can we disable "Prevent Automatic RDF Link Recovery" option for RDFG
group on 5773 with SE 7.1.
D:\dmx\sdt24dbho2_dg>symrdf -sid 301 -rdfg 21 set rdfg
-autolink_recovery on -both_sides
'rdfg': Invalid keyword.
Thanks & Regards ,
Basavaraju Y
Storage Administrator
Information Technology Group
Phone: 02-6984174 - ext: 1174
0_Specialist
GEMC
36 Posts
0
September 14th, 2012 22:00
Hi
1. Create clone session with precopy.
2. Once precopy is at 100%, split R1 and R2 ( I guess this step is not required)
3. Activate clone session. ==> Activating the clone session will normally make your target clone device as RW and host can access the target clone LUN. Why we need step 4?
4. Once session status is copied, next step clone session split. ==> Your clone session should be in restored state if you want to perform Split. You can't split the clone session when it is in copied state.
Correct me if I am wrong.
Thanks
ybraju_unb
14 Posts
0
September 26th, 2012 08:00
Thanks Govind, I did it manually by moving the RDF pairs, deleting the
RDF group and re creating RDFG group with auto link recovery option.
Thanks & Regards ,
Basavaraju Y
Storage Administrator
Information Technology Group
Phone: 02-6984174 - ext: 1174
0_Specialist
Govindagouda
85 Posts
0
September 26th, 2012 08:00
I just found this on the Primus
This is a new option which is available from micro code version 5875 and above and not in 5874, but in the document its not