Hi there,

I have an MD3420 that is no longer starting up. The unit has 2 controllers, both of which recently required a new RTC battery be installed which was done.

After replacing the battery both units will not boot. The messages I am seeing via the serial console are different per controller. I cannot seem to continue or abort or etc, the controllers just don't seem to respond to key strokes. Not sure if that is an issue with the cable or not.

For controller 0 I am seeing:

-=<###>=- reading fw/active/System

8276978 bytes read

Adding 18180 symbols for standalone.
wrproxy:Instantiating /bd0 as rawFs, device = 0x10001

RTC Error: Real-time clock device is not working

RTC Warning: Battery for real-time clock and NVSRAM must be replaced
/bd16/fw/staged/: errno = 0x380003
usrSecurity: error adding default user '(null)' to the system (errno = 0x16)!
Instantiating /ram as rawFs, device = 0x80001
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x80001
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 1c60000
Label:" " ...
Disk with 1024 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 1010 clusters, 3 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 6
Root dir entries 112, sysId VXDOS12 , serial number 1c60000
Label:" " ...
OK.

 

Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
3900 Real-Time Clock
01 RT Clock Tick ** Failed **

*** Error (0005): Real time clock/NVSRAM battery low

STATUS: Real time clock/NVSRAM battery low

*** Current Loop Count: 1 Date: 03/31/2014 Time: 05:36:39

*** Master Error Code: 2701-3900-01-0005

D)isplay R)etry C)ontinue M)onitor Shell A)bort ?

And for Controller 1 I am seeing:

 

-=<###>=- reading fw/active/System

8276978 bytes read

Adding 18180 symbols for standalone.
wrproxy:Instantiating /bd0 as rawFs, device = 0x10001

RTC Error: Real-time clock device is not working

RTC Warning: Battery for real-time clock and NVSRAM must be replaced
/bd16/fw/staged/: errno = 0x380003
Unexpected PCI bus width 0(8) for BDF[1,8,0]
Unexpected PCI bus speed 1(3) for BDF[1,8,0]
TRIGGERING LOCKDOWN.

PCI DEVICE 5 NOT FOUND: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x60400 ParentBridge=PLX PCI-E Bridge to Host Card
TRIGGERING LOCKDOWN.

PCI DEVICE NOT ACCESSIBLE: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x60400 ParentBridge=PLX PCI-E Bridge to Host Card

PCI DEVICE 0 NOT FOUND: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card
TRIGGERING LOCKDOWN.

PCI DEVICE NOT ACCESSIBLE: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card

PCI DEVICE NOT ACCESSIBLE: PLX PCI-E Bridge to Host Card SAS Host Port 0 Device=9 Function=0 ClassCode=0x60400 ParentBridge=Host Card PLX PCI-E Switch

PCI DEVICE 0 NOT FOUND: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card
TRIGGERING LOCKDOWN.

PCI DEVICE NOT ACCESSIBLE: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card

PCI DEVICE NOT ACCESSIBLE: PLX PCI-E Bridge to Host Card SAS Host Port 0 Device=9 Function=0 ClassCode=0x0 ParentBridge=Host Card PLX PCI-E Switch

PCI DEVICE NOT ACCESSIBLE: Host-side SAS Device=0 Function=0 ClassCode=0x10700 ParentBridge=PLX PCI-E Bridge to Host Card SAS Host Port 0

PCI DEVICE 0 NOT FOUND: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card
TRIGGERING LOCKDOWN.

PCI DEVICE NOT ACCESSIBLE: Host Card PLX PCI-E Switch Device=0 Function=0 ClassCode=0x0 ParentBridge=PLX PCI-E Bridge to Host Card

PCI DEVICE NOT ACCESSIBLE: PLX PCI-E Bridge to Host Card SAS Host Port 0 Device=9 Function=0 ClassCode=0x0 ParentBridge=Host Card PLX PCI-E Switch

PCI DEVICE NOT ACCESSIBLE: Host-side SAS Device=0 Function=0 ClassCode=0x10700 ParentBridge=PLX PCI-E Bridge to Host Card SAS Host Port 0
03/07/14-02:05:05 (tSystem): NOTE: I2C transaction returned 0x8011e000
Error
usrSecurity: error adding default user '(null)' to the system (errno = 0x16)!
Instantiating /ram as rawFs, device = 0x50001
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x50001
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 1ca0000
Label:" " ...
Disk with 1024 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 1010 clusters, 3 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 6
Root dir entries 112, sysId VXDOS12 , serial number 1ca0000
Label:" " ...
OK.
PLX device not found. Was expecting to find Device ID 8724
Could not determine ntbBridgeBase. Bailing out.

 

Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
3900 Real-Time Clock
01 RT Clock Tick ** Failed **

*** Error (0005): Real time clock/NVSRAM battery low

STATUS: Real time clock/NVSRAM battery low

*** Current Loop Count: 1 Date: 03/07/2014 Time: 02:05:07

*** Master Error Code: 2701-3900-01-0005

D)isplay R)etry C)ontinue M)onitor Shell A)bort ?

Does this mean that both controllers are now unusable? I also noticed that the fans will continuously run at full speed until I remove Controller 1.