Data Domain - 透過命令列介面 （CLI） 設定實體介面

Summary: 此 kb 的建立旨在提供命令，說明如何透過 data domain 上的命令列介面設定實體介面。

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Instructions

如果您只是將 Data Domain 移至新網站，並且想要重新設定所有新功能，您也可以執行 config 設定命令。

如果您只想要設定網路，請略過組態設定命令，然後只使用此 kb 的 net 命令。 

# config setup

Launch a utility program that prompts you to configure settings for the system, network, filesystem, CIFS, NFS, and licenses. Press Enter to cycle through the selections and confirm any changes when prompted. Choices include Save, Cancel, and Retry.

This command option is unavailable on Retention Lock Compliance systems. Use System Manager to change configuration settings. Role required: admin and limited-admin.
Net config 命令可讓您設定 DD 上的實體介面。  
 # net config  [type {floating | fixed}]
                {[] [netmask ] | [] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu { | default}]
                [txqueuelen ]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. "Note:
                                       Change of link parameters like speed,
                                       duplex or autoneg on the DD VE is not
                                       supported."

Example # net config ethXx x.x.x.x netmask x.x.x.x 

To clear a interface give a address of zeros. 

Example # net config ethXx 0.0.0.0

如果您需要在第一次設定資料網域上變更預設閘道，或將 Data Domain 移至新位置，則可以使用 net 路由設定閘道命令。

注意：遠端設定預設閘道時請注意，因為您可能會失去對 Data Domain 的完整存取權。最好在 idrac 命令主控台中使用此命令，或是直接串列連線至資料中心現場的 DD 時使用此命令。  
# net route set gateway { | }
                                       Set the default gateway
如果您只需要新增閘道，您可以使用 Net 路由新增閘道命令。  
# net route add gateway  [interface ]
                                       Add a default gateway address,
                                       optionally to a specific interface
注意： dd3300 無法使用 net aggregate 命令，因為它不支援匯總，僅支援容錯移轉。 
  
 # net aggregate add  interfaces 
                [mode {roundrobin |
                balanced hash {xor-L2 | xor-L3L4 | xor-L2L3} |
                lacp hash {xor-L2 | xor-L3L4 | xor-L2L3}
                [rate {fast | slow}]}]
                [up { | default}]
                [down { | default}]
                                       Add slave interfaces to an aggregate
                                       interface. Mode must be given the first
                                       time

 # net aggregate del  interfaces { | all}
                                       Delete network interfaces from an
                                       aggregate interface

 # net aggregate modify 
                [mode {roundrobin |
                balanced hash {xor-L2 |xor-L3L4| xor-L2L3} |
                lacp hash {xor-L2|xor-L3L4|xor-L2L3}
                [rate {fast | slow}]}]
                [up { | default}]
                [down { | default}]
                                       Modify the configuration of an
                                       aggregate interface. Mode must be given
                                       the first time

 # net aggregate show                   Display all aggregate interfaces

 #  net config  [type {floating | fixed}]
                {[] [netmask ] | [] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu { | default}]
                [txqueuelen ]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. "Note:
                                       Change of link parameters like speed,
                                       duplex or autoneg on the DD VE is not
                                       supported."

 # net config addresses [type {floating | fixed}]
                                       Convert IP addresses to another type.

 # net create interface { | }
                {vlan  | alias }
                                       Create a VLAN interface or an IP Alias
                                       Interface

 # net create virtual veth          Create a virtual interface

 # net destroy { |  |  }
                                       Destroy a VLAN or IP Alias or Virtual
                                       interface

 # net disable                  Disable an Ethernet interface

 # net enable                   Enable an Ethernet interface

 # net failover add  interfaces 
                [primary ]
                [up { | default}]
                [down { | default}]
                                       Add network interfaces to a failover
                                       interface

 # net failover del  interfaces { | all}
                                       Delete network interfaces from a
                                       failover interface

 # net failover modify  [primary { | none}]
                [up { | default}]
                [down { | default}]
                                       Modify the primary network interface
                                       for a failover interface

 # net failover show                    Display all failover interfaces

 # net modify  bonding {aggregate | failover}
                                       Change the bond mode between failover
                                       and aggregate

 # net ping { | |  [ipversion {ipv4 | ipv6}]}
                [broadcast] [count ] [interface ]
                [packet-size ] [path-mtu {do | dont | want}]
                [pattern ] [numeric] [verbose]
                                       Ping a host. Param 'broadcast' is for

 # net show all                         Display all networking information

 # net show config []           Display the configuration for the
                                                             Ethernet interface

 # net show hardware                    Display Ethernet port information

 # net show hostname [type {local|ha-system}]
                                       Display the hostname

 # net show settings                    Display Ethernet interface settings

 # net show stats [[ipversion {ipv4 | ipv6}] [all | listening] [detailed] |
                [ipversion {ipv4 | ipv6}] route | interfaces |
                [ipversion {ipv4 | ipv6}] statistics]
                                       Display network statistics

 # net troubleshooting duplicate-ip     Detect duplicate IP in network





 

 

Additional Information

HTTPs://www.dell.com/support/kbdoc/en-us/000013760 Data Domain - 將 Data Domain 從一個月臺移到另一個
站點 HTTPs://www.dell.com/support/kbdoc/en-us/000209434使用圖形使用者介面 （GUI） 設定實體介面

Affected Products

Data Domain
Article Properties
Article Number: 000213048
Article Type: How To
Last Modified: 13 Oct 2023
Version:  2
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.