Dell EMC PowerEdge R440 Installation and Service Manual

PDF

Back view of the system

The back view displays the features available on the back of the system.

Back view of the system with full height riser — Figure 1. Back view of the system with full height riser

Table 1. Back view of the system with full height riserItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the hard drive, enables you to install drives that are supported in your system. Item 3 is the power supply unit, supplies power to the components of the system. Item 4 is the NIC port, integrated on the network daughter card (NDC) provides network connectivity. Item 5 is the USB 3.0 port, enables you to connect USB devices to the system. Item 6 is the video port, enables you to connect a display device to the system. Item 7 is the serial port, enables you to connect serial device to the system. Item 8 is the iDRAC 9 Enterprise port, enables you to remotely access iDRAC. Item 9 is the System status indicator cable port, enables you to connect to cable management arm LED. Item 10 is the System identification button, helps in identifying the system in a rack.
Item	Ports, panels, or slots	Icon	Description
1	Serial port		Use the serial port to connect a serial device to the system. For more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals .
2	iDRAC9 dedicated network port	NA	Use the iDRAC9 dedicated network port to securely access the embedded iDRAC on a separate management network, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals
3	Ethernet ports (2)		Use the Ethernet ports to connect Local Area Networks (LANs) to the system. For more information about the supported Ethernet ports, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
4	Full height riser slot	N/A	Use the card slots to connect full-height PCIe expansion cards on full height riser.
5	Power supply unit (PSU)	N/A	For more information about the PSU configurations, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
6	Power supply unit (PSU)	N/A	For more information about the PSU configurations, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
7	LOM riser ports (2)		For more information about the PSU configurations, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
8	USB 3.0 port (2)		Use the USB 3.0 port to connect USB devices to the system. These ports are 4-pin, USB 3.0-compliant.
9	VGA port		Use the VGA port to connect a display to the system. For more information about the supported VGA port, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals .
10	System status indicator cable port	N/A	Enables you to connect the status indicator cable and view system status when the CMA is installed.
11	System identification button		Press the system ID button: To locate a particular system within a rack. To turn the system ID on or off. To reset iDRAC, press and hold the button for more than 15 seconds. NOTE To reset iDRAC using system ID, ensure that the system ID button is enabled in the iDRAC setup. If the system stops responding during POST, press and hold the system ID button (for more than five seconds) to enter the BIOS progress mode.

Back view of the system with 2 risers — Figure 2. Back view of the system with 2 risers

Table 2. Back view of the system with 2 risersItem 1 is the PCIe expansion card slot(s), enables you to connect to PCI Express expansion cards. Item 2 is the hard drive, enables you to install drives that are supported in your system. Item 3 is the power supply unit, supplies power to the components of the system. Item 4 is the NIC port, integrated on the network daughter card (NDC) provides network connectivity. Item 5 is the USB 3.0 port, enables you to connect USB devices to the system. Item 6 is the video port, enables you to connect a display device to the system. Item 7 is the serial port, enables you to connect serial device to the system. Item 8 is the iDRAC 9 Enterprise port, enables you to remotely access iDRAC. Item 9 is the System status indicator cable port, enables you to connect to cable management arm LED. Item 10 is the System identification button, helps in identifying the system in a rack.
Item	Ports, panels, or slots	Icon	Description
1	Serial port		Use the serial port to connect a serial device to the system. For more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals .
2	iDRAC9 dedicated network port	NA	Use the iDRAC9 dedicated network port to securely access the embedded iDRAC on a separate management network, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals
3	Ethernet ports (2)		Use the Ethernet ports to connect Local Area Networks (LANs) to the system. For more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
4	Low profile riser right slot	N/A	Use the card slot to connect half-height PCIe expansion card on low profile riser.
5	Low profile riser left slot	N/A	Use the card slot to connect half-height PCIe expansion card on low profile riser.
6	Cabled PSU	N/A	FFor more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
7	LOM riser ports (2)		For more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
8	USB 3.0 port (2)		Use the USB 3.0 port to connect USB devices to the system. These ports are 4-pin, USB 3.0-compliant.
9	VGA port		Use the VGA port to connect a display to the system. For more information, see the PowerEdge R440 Technical Specs at www.dell.com/poweredgemanuals
10	System status indicator cable port	N/A	Enables you to connect the status indicator cable and view system status when the CMA is installed.
11	System identification button		Press the system ID button: To locate a particular system within a rack. To turn the system ID on or off. To reset iDRAC, press and hold the button for more than 15 seconds. NOTE To reset iDRAC using system ID, ensure that the system ID button is enabled in the iDRAC setup. If the system stops responding during POST, press and hold the system ID button (for more than five seconds) to enter the BIOS progress mode.