- Notes, Cautions, and Warnings
- About Your System
- Front-Panel Features And Indicators—Tower Mode
- Front-Panel Features And Indicators—Rack Mode
- LCD Panel Features
- Diagnostic Indicators
- Hard-Drive Indicator Patterns
- Back-Panel Features And Indicators
- NIC Indicator Codes
- Power Indicator Codes For Redundant Power Supply
- Power Indicator Codes For Non-Redundant Power Supply
- Other Information You May Need
- Using The System Setup And Boot Manager
- Installing System
Components
- Recommended Tools
- Front Bezel (Optional)
- System Feet—Tower Mode
- Wheel Assembly (Optional)—Tower Mode
- Opening And Closing The System
- Inside The System
- Optical Drives And Tape Drives (Optional)
- Cooling Shroud
- Hard Drives—Hot-Swappable
- Removing a Hot-Swap Hard Drive
- Installing A Hot-Swap Hard Drive
- Removing A 2.5 Inch Hard-Drive Blank
- Installing A 2.5 Inch Hard-Drive Blank
- Removing A 3.5 Inch Hard-Drive Blank
- Installing A 3.5 Inch Hard-Drive Blank
- Removing A 2.5 Inch Hard Drive From A 3.5 Inch Hard-Drive Adapter
- Installing A 2.5 Inch Hard Drive Into A 3.5 Inch Hard-Drive Adapter
- Removing A Hard Drive Or A Hard-Drive Adapter From A Hard-Drive Carrier
- Installing A Hard Drive Or A Hard-Drive Adapter Into A Hard-Drive Carrier
- Hard Drives—Cabled
- Hard-Drive Backplane
- Four-Slot Hard-Drive Blank
- System Memory
- Cooling Fans
- Internal USB Memory Key (Optional)
- PCIe Card Holder (Optional)
- Expansion Cards
- iDRAC Ports Card
- Internal Dual SD Module
- Internal SD Card
- Processors
- Redundant AC Power Supply
- Non-Redundant AC Power Supply
- Power Distribution Board And Power Interposer Board
- System Battery
- Control-Panel
Assembly
- Removing The Control-Panel Assembly
- Installing The Control-Panel Assembly
- Removing The Control Panel
- Installing The Control Panel
- Removing The Control-Panel Board For Systems With LCD Modules
- Installing The Control-Panel Board For Systems With LCD Modules
- Removing The Control-Panel Board For Systems With Diagnostic Indicators
- Installing The Control-Panel Board For Systems With Diagnostic Indicators
- Removing The LCD Module
- Installing The LCD Module
- Removing The VGA Module—Rack Mode
- Installing The VGA Module—Rack Mode
- System Board
- Converting The System From Tower Mode To Rack Mode
- Troubleshooting
Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting The Video Subsystem
- Troubleshooting A USB Device
- Troubleshooting A Serial I/O Device
- Troubleshooting A NIC
- Troubleshooting A Wet System
- Troubleshooting A Damaged System
- Troubleshooting The System Battery
- Troubleshooting A Non-Redundant Power Supply
- Troubleshooting Redundant Power Supplies
- Troubleshooting Cooling Problems
- Troubleshooting Cooling Fans
- Troubleshooting System Memory
- Troubleshooting An Internal USB Key
- Troubleshooting An SD Card
- Troubleshooting An Optical Or Tape Drive
- Troubleshooting A Hard Drive
- Troubleshooting Expansion Cards
- Troubleshooting Processor
- Using System Diagnostics
- Jumpers And Connectors
- Technical Specifications
- System Messages
- Getting Help
Benvenuto
Benvenuto in Dell
Il mio account
- Effettua gli ordini in modo rapido e semplice
- Visualizza gli ordini e monitora lo stato della spedizione
- Crea e accedi a un elenco dei tuoi prodotti
- Gestisci i siti, i prodotti e i contatti per livello di prodotto di Dell EMC tramite l'amministrazione della società.
Dell PowerEdge T320 Systems Owner's Manual
Back-Panel Features And Indicators
Figure 1. Back-Panel Features
and Indicators
| Item | Indicator, Button, or Connector | Icon | Description |
|---|---|---|---|
| 1 | Power supplies (PSU1 and PSU2) | ||
| 2 | PCIe expansion card slots (5) | Allow you to connect up to five full-height PCIe expansion cards. | |
| 3 | vFlash media card slot |  | Allows you to insert a vFlash media card. |
| 4 | iDRAC7 Enterprise port | ||
| 5 | System identification button |  | The identification buttons on the front
and back panels can be used to locate a particular system within a
rack. When one of these buttons is pressed, the LCD panel on the front
and the system status indicator on the back flash until one of the
buttons is pressed again.
Press to toggle the system ID on and off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter the BIOS progress mode. To reset iDRAC (if not disabled in F2 iDRAC setup), press and hold for more than 15 seconds. |
| 6 | System identification connector | Allows you to connect the optional system status indicator assembly through the optional cable management arm. | |
| 7 | USB connectors (6) |  | Allow you to connect USB devices to the system. The ports are USB 2.0-compliant. |
| 8 | Ethernet connectors (2) |  | Two integrated 10/100/1000 Mbps NIC connectors. |
| 9 | Video connector |  | Allows you to connect a VGA display to the system. |
| 10 | Serial connector |  | Allows you to connect a serial device to the system. |
| 11 | External cooling fan power cable slot | Slot for routing the power cable of the optional external cooling fan into the chassis. |
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Fornisci una valutazione (1-5 stelle).
Indica se l'articolo è stato utile o meno.
I commenti non possono contenere i seguenti caratteri speciali: <>() \