Dell EMC OpenManage SNMP Reference Guide Version 9.1

PDF

Baseboard Management Controller Group Variable Values

This section includes definitions for server administrator-specific variable values used in this section.

Table 1. Baseboard Management Controller . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBMCSerialConnectionModeCapabilities` Data Type: `Integer` These values are bit masks; therefore, combination values are possible.

Possible Data Values	Meaning of Data Value
`-- none(0)`	No mode capabilities.
`modemBasic(1)`	BMC serial interface supports Modem Basic mode.
`modemPPP(2)`	BMC serial interface supports Modem Point to Point Protocol (PPP) mode.
`modemTerminal(4)`	BMC serial interface supports Modem Terminal mode.
`directBasic(8)`	BMC serial interface supports Direct Basic mode.
`directPPP(16)`	BMC serial interface supports Direct PPP mode.
`directTerminal(32)`	BMC serial interface supports Direct Terminal mode.

Table 2. BMC Serial Connection Mode Settings . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBMCSerialConnectionModeSettingsDellBMCSerialConnectionModeCapabilities` Data Type: `Integer` These values are bit masks; therefore, combination values are possible.

Possible Data Values	Meaning of Data Value
`-- none(0)`	No modes enabled.
`modemBasic(1)`	Modem Basic mode is enabled.
`modemPPP(2)`	Modem PPP mode is enabled.
`modemTerminal(4)`	Modem Terminal mode is enabled.
`directBasic(8)`	Direct Basic mode is enabled.
`directPPP(16)`	Direct PPP mode is enabled.
`directTerminal(32)`	Direct Terminal mode is enabled.

Table 3. BMC Serial Flow Control Type . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBMCSerialFlowControlType` Data Type: `Integer`

Possible Data Values	Meaning of Data Value
`-- none(0)`	No flow control used.
`rtscts(1)`	RTS/CTS (hardware) flow control used.
`xonXoff(2)`	XON/XOFF flow control used.

Table 4. BMC Serial Bit Rate Type . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBMCSerialBitRateType` Data Type: `Integer`

Possible Data Values	Meaning of Data Value
`bps9600(6)`	Bit rate is 9600 bps (bits per second)
`bps19200(7)`	Bit rate is 19200 bps
`bps38400(8)`	Bit rate is 38400 bps
`bps57600(9)`	Bit rate is 57600 bps
`bps115200(10)`	Bit rate is 115200 bps

Table 5. BMC LAN IP Address Source Type . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBMCLANIPAddressSourceType` Data Type: `Integer`

Possible Data Values	Meaning of Data Value
`-- unspecified(0)`	Source is unspecified.
`static(1)`	IP address is static.
`dhcp(2)`	Dynamic Host Configuration Protocol (DHCP) used to obtain IP address.
`biosOrSystemSoftware(3)`	BIOS or system software provided IP Address.
`other(4)`	Other protocol used to obtain IP address.

Table 6. BMC Management Controller Type . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellManagementControllerType` Data Type: `Integer`

Possible Data Values	Meaning of Data Value
`-- legacyBMC(0)`	Controller type is legacy Baseboard Management Controller.
`iDRAC(8)`	Controller type is iDRAC.
`iDRAC6(10)`	Controller type is Integrated Dell Remote Access Controller 6.
`iDRAC6Modular(11)`	Controller type is Integrated Dell Remote Access Controller 6 (Modular).
`iDRAC6BMC(13)`	Controller type is Integrated Dell Remote Access Controller 6 (BMC mode).
`iDRAC7(16)`	Controller type is Integrated Dell Remote Access Controller 7.
`iDRAC7Modular(17)`	Controller type is Integrated Dell Remote Access Controller 7 (Modular).
`vrtxCMC(18)`	Controller type is VRTX Chassis Management Controller (CMC).
`fx2CMC(19)`	Controller type is FX2 Chassis Management Controller (CMC).
`iDRAC8(32)`	Controller type is Integrated Dell Remote Access Controller 8.
`iDRAC8Modular(33)`	Controller type is Integrated Dell Remote Access Controller 8 (Modular).

Table 7. Dell Blade Form Factor Type . The following table describes the variable name, data type, the possible data values and the meaning of each possible data value.
Variable Name: `DellBladeFormFactorType` Data Type: `Integer`

Possible Data Values	Meaning of Data Value
`formFactorTypeIsSingleWidthHalfHeight(1)`	Form Factor Type is singleWidthHalfHeight.
`formFactorTypeIsDualWidthHalfHeight(2)`	Form Factor Type is DualWidthHalfHeight.
`formFactorTypeIsSingleWidthFullHeight(3)`	Form Factor Type is SingleWidthFullHeight.
`formFactorTypeIsDualWidthFullHeight(4)`	Form Factor Type is DualWidthFullHeight.
`formFactorTypeIsSingleWidthQuarterHeight(5)`	Form Factor Type is SingleWidthQuarterHeight.
`formFactorTypeIs1UHalfWidth(6)`	Form Factor Type is 1UHalfWidth.
`formFactorTypeIs1UQuarterWidth(7)`	Form Factor Type is 1UQuarterWidth.
`formFactorTypeIs1UFullWidth(8)`	Form Factor Type is 1UFullWidth.
`notApplicable(256)`	Form Factor Type is Not Applicable for the system.