- Notes, cautions, and warnings
- Dell PowerEdge C6320 product overview
- Supported configurations for PowerEdge C6320 system
- Accessing system features during startup
- Front panel features and indicators
- Hard drive indicator patterns
- Back panel features and indicators
- LAN indicator codes
- Power and system board indicator codes
- Power Supply Unit indicator codes
- Baseboard Management Controller (BMC) heart beat LED
- System configuration limitations by Intel Xeon processor E5-2600 v3 and E5-2600 v4 product family
- Locating your system Service Tag
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- System cover
- Inside the system
- Cooling fans
- Hard drives
- Removing a 3.5-inch hard drive blank
- Installing a 3.5-inch hard drive blank
- Removing a 2.5-inch hard drive blank
- Installing the 2.5-inch hard drive blank
- Removing a hard drive carrier
- Installing a hard drive carrier
- Removing a hard drive from a hard drive carrier
- Installing a hard drive into a hard drive carrier
- Installing a 2.5-inch SSD into a 3.5-inch hard drive carrier
- SSD and SSD holder
- SATADOM
- Power supply units
- System board tray
- System board assembly
- Cooling shroud
- Heat sinks
- Processors
- Expansion card assembly and expansion card
- PCI-E slot priority
- PERC cards
- Riser card
- Optional mezzanine cards
- Mezzanine card bridge board
- System memory
- System battery
- System board
- Trusted Platform Module
- Power distribution boards
- Midplanes
- Hard drive backplanes
- 2.5-inch hard drive expander configuration
- Control panel
- Sensor board
- Removing the sensor board for 3.5-inch hard drive system
- Installing the sensor board for 3.5-inch hard drive system
- Cable routing for sensor board and control panel for 3.5-inch hard drive system
- Removing the sensor board for 2.5-inch hard drive system
- Installing the sensor board for 2.5-inch hard drive system
- Cable routing for sensor board and control panel for 2.5-inch hard drive system
- Jumpers and connectors
- Troubleshooting your system
- Installation Problems
- Minimum configuration to POST
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Dell PowerEdge C6320 Owner's Manual
Accessing system features during startup
The following
keystrokes provide access to system features during startup.
NOTE: The hot keys of SAS or SATA
card or PXE support are available in BIOS boot mode only. There is
no hot key to boot in the UEFI mode.
- Keystroke
- Description
- F2
- Enters the System Setup program.
- F11
- Enters the BIOS Boot Manager.
- F12
- Starts Preboot eXecution Environment (PXE)/iSCSI boot.
- Ctrl +C
- Enters the LSI 2008 SAS Mezzanine Card Configuration Utility. For more information, see the SAS adapter documentation.
- Ctrl+R
- Enters the PERC 9 Card Configuration Utility. For more information, see the documentation for your SAS RAID card.
- Ctrl+Y
- Enters the MegaPCLI SAS RAID Management Tool.
- Ctrl+S
- Enters the utility to configure onboard LAN settings for PXE boot. For more information, see the documentation for your integrated LAN.
- Ctrl+I
- Enters onboard SATA Controller’s Configuration Utility.
- Ctrl+D
- Enters the Intel iSCSI setup menu.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\