Search Results (1.4K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
System Model: PowerEdge R720Operating System: Windows Server 2012 R2BIOS Version: 1.6.0iDRAC7 Firmware Version: 1.66.65 (Build 07)Lifecycle Controller Firmware: 1.1.5.165 Start of following events: 2023-01-22 17:34 Used Lifecycle to execute Dell Update Package BIOS_8P8WX_WN32_2.9.0.EXE and receive
Question
•
Systems Management General
Community Accepted Solution
Hi,I am trying to re-configure the IDRAC from racadm (can't reach from network). I am getting this: racadm getniccfg IPv4 settings: NIC Enabled = 1 IPv4 Enabled = 1 DHCP Enabled = 1 IP Address = 10.0.100.202 Subnet Mask = 255.255.255.0 Gateway
Question
•
Systems Management General
Community Accepted Solution
Hello Community , i am new to RDM so my question might be straight forward. i installed the newest version of DRM :3.4.3 and i have created a customized catalog for our servers.. i have exported the catalog to a local disk and enabled the destination folder to be an SMB share , however when i go
Question
•
Dell Repository Manager
Community Accepted Solution
Hello, Since a few weeks now (can't really find out when), for my x30s, there is a very old firmware "downgrade" proposed by Dell OME : I found a newer one available since December 2022 but it doesn't show up and anyway, such a downgrade is my opinion not OK : https://www.dell.com/support/
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hi Team .. Service Tag could not be verified while updating firmware. we have done the 2 proccess below: 1- enabled V1 in the Appliance share setting 2- updated BIOS & Idrac manually we still facing same issue. Br/ Khiyar Issa
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hi, I have a couple of iDRAC7 that now fail to search for firmware upgrades from downloads.dell.com.When looking at Job Queue.The error message is RED060: The specified repository catalog is not supported. Has the Catalog.xml changed format?
Question
•
Systems Management General
Community Accepted Solution
Hi, today I've noticed that for all of my yx2x systems firmware is not available. There is an info that update file not in catalog. According to support matrix that hardware should be supported. Last week everything was fine and I was able to update yx2x systems. Do you know what is going on?
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
OpenManage Enterprise says I need to upgrade my iSM LC DUP to version 5.0.1.0 for my PowerEdge R650, but the support website doesn't have any links to version 5.0.1, where can I download it? If I put in my service tag, the latest version available on the support website is version 4.3.0.0. The li
Question
•
Systems Management General
Community Accepted Solution
The PC does not Post and has error code 1,4 and amber light and pressing the power button shows code 3. It is a Core 4 with 4 GB RAM.
Question
•
Systems Management General
Community Accepted Solution
Hello, I have a Poweredge R730 and the CPU temp is always at 62-64 degrees Celsius, this is about 15 degrees hotter than the same server types in the same comms room and rack. Does this seem abnormally high? Interestingly the fans are running about 500 rpm lower than the other models. I have ch
Question
•
Systems Management General
Community Accepted Solution
Hello, I´m trying to deploy a Profile for Dell Poweredge R740 Server. I´ve discovered the template automatically from a reference server and then putted into a new profile. The Profile is available but when I try to deploy it, there is no target device available for selection. I can see only empty
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Just installed OpenManage Administrator Node 10.3 and got the error "Windows can't verify the publisher of this driver software". Why does Dell have software with unsigned drivers!? This threatens the stability of my servers. Did Dell's OpenManage software get infected or is Dell just lazy??
Question
•
Systems Management General
Community Accepted Solution
Hello , When i try to register the register the Service Plugin from OpenManage Enterprise first i see an Window where i have to fill out an Access key and an PIN . But i dont have this Informations . Therefore i choose "Generate Access key and PIN" , then i was redirected on an Website .&nb
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
OME 3.9 (Build 55), Discovery for IDRAC with WSMAN. All old servers (R620) were discovered with no problem. all new servers (R650, R640, R630) failed. Unable to perform the requested action because the device management endpoint authentication over WSMAN, REDFI
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hi, I would like to check if Dell Poweredge Server are impacted by the above mentioned Intel security advisories https://www.intel.com/content/www/us/en/security-center/default.html Regards Soh
Question
•
Systems Management General
Community Accepted Solution
I don't see this for download under any service tag we have. Is there somewhere to download this publicly? Just trying to find a way to update a BIOS.
Question
•
Systems Management General
Community Accepted Solution
I have been using a small cli script assembled from the .jar files listed in the .jnlp file you get when you start the java console. It's pretty basic, I have one for idrac6 and one for idrac7/8/9. @echo offpushd %~dp0%set PATH=jre8-Windows\bin;%PATH%java ^ -cp avctKVM.jar ^ com.avocent.idrac.kvm
Question
•
Systems Management General
Community Accepted Solution
I have an Avigilon NVR that's running server 2012 r2. The server is out of warranty so I can't get any help from Dell. The server administrator will not accept credentials. No errors, just keeps prompting. I've read the articles about Java and it has no other version and the latest is installed. Tha
Question
•
Systems Management General
Community Accepted Solution
Latest catalog contains a network firmware released in in 2017 [root@6510c93514ca /]# drm --details -r=C6420_bms:1.20 | grep -i net|__ Network_Firmware_HJP7D_LN64_16.00.19_A00-00.BIN 16.00.19 22.66 MB|__ Network_Firmware_7N5GW_WN64_10.01.00_A00-00.EXE 10.01.00 13.11 MB previous catalog had the sam
Question
•
Dell Repository Manager
Community Accepted Solution
Some essential tasks can only be performed in TUI. There is an entire section Configure OpenManage Enterprise by using Text User Interface in the user manual. How to I get onto the TUI? I am using an appliance installed in KVM on CentOS Linux. When I searched the manual, the
Question
•
Dell OpenManage Essentials