SONiC do Dell Networking: Protocolo de resolução de endereço IPv4
摘要: Este artigo explica sobre o protocolo de resolução de endereçoS IPv4 no Dell Networking SONiC. Este artigo usa um comutador que executa o Dell SONiC 4.1.
本文章適用於
本文章不適用於
本文無關於任何特定產品。
本文未識別所有產品版本。
說明
|
Pré-requisitos
Estamos usando a nomenclatura de interface padrão para demonstrar os conceitos. Consulte o artigo da Dell 202172 Dell Networking Série S: Configuração básica de interface - SONiC 4.0 para obter mais informações sobre nomenclatura de interface |
Índice
Introdução
Exibir entradas do protocolo de resolução de endereço IPv4.
Limpar entradas IPv4
Introdução
O Protocolo de resolução de endereços (ARP) permite que os pacotes IPv4 sejam enviados entre redes, traduzindo endereços IP de rede para endereços de hardware MAC e endereços MAC para endereços IP. O endereço MAC e o endereço IP correspondente dos dispositivos de destino são mantidos na tabela ARP. Usando o endereço IP, a tabela ARP permite que o comutador recupere rapidamente o endereço MAC associado, encapsular o pacote IP em um quadro L2 e transmiti-lo pela rede para um destino.Exibir entradas ARP IPv4
Para exibir entradas da tabela ARP, use o comando show ip arp . Para filtrar a saída, especifique uma interface, port channel ou VLAN, um endereço IP no formato x.x.x.x, um endereço MAC ou uma combinação de mais de um valor para corresponder. Você também pode exibir informações resumidas e as entradas ARP IPv4 em um VRF especificado.Sintaxe do comando
admin@DELLSONiC:~$ sonic-cli DELLSONiC# configure DELLSONiC(config)#show ip arp |
DELLSONiC# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.1xx.1.4 00:01:02:03:44:55 Eth1/3 - Dynamic Fwd 192.1xx.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 192.1xx.3.6 00:01:02:03:04:05 Vlan100 Eth1/2 Dynamic Fwd 10.11.48.2xx 00:01:e8:8b:44:71 Management0 - Dynamic Fwd 0.0.0.0 00:00:00:00:00:00 lo - Dynamic Fwd |
Nota: A última entrada ARP para o endereço IP de loopback 0.0.0.0 pode ser inserida a partir do sonic NEIGH_TABLE de APPL_DB. Para excluir a entrada, você deve excluí-la manualmente do REDIS_DB usando o redis-cli ou qualquer outro aplicativo que permita editar o REDIS_DB.
DELLSONiC# show ip arp interface Vlan 20 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd 20.0.0.5 00:11:22:33:44:55 Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp 20.0.0.2 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp mac-address 90:b1:1c:f4:9d:ba Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd |
DELLSONiC# show ip arp summary Total Entries ------------- 2 |
DELLSONiC# show ip arp vrf Vrf_1 Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ----------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ----------------------------------------------------------------------- 20.0.0.2 90:b1:1c:f4:9d:ba Vlan20 Eth1/1 Dynamic Fwd 20.0.0.5 00:11:22:33:44:55 Vlan20 Eth1/1 Dynamic Fwd |
Limpar entradas IPv4
Para excluir entradas IPv4 aprendidas dinamicamente da tabela ARP, use o comando clear ip arp. Para especificar as entradas a serem excluídas, digite uma interface, port channel ou VLAN, um endereço IPv4 ou uma combinação para corresponder. Digite force para excluir entradas ARP configuradas estaticamente. Use o comando show ip arp para verificar se as entradas IPv4 foram excluídas. DELLSONiC# clear ip arp < [interface {Eth slot/port[/breakout-port] | PortChannel number | Vlan vlanid | Management port-number}] [ip-address] [vrf vrf-name]> |
DELLSONiC# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.168.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 192.168.3.6 00:01:02:03:04:05 Vlan100 Eth1/2 Dynamic Fwd 10.11.48.254 00:01:e8:8b:44:71 Management0 - Dynamic Fwd sonic# clear ip arp interface Vlan 100 sonic# show ip arp Type: R - Remote Neighbor entries (EVPN or MCLAG Separate IP) ------------------------------------------------------------------------------------- Address Hardware address Interface Egress Interface Type Action ------------------------------------------------------------------------------------- 192.168.2.4 00:01:02:03:ab:cd PortChannel200 - Dynamic Fwd 10.11.48.254 00:01:e8:8b:44:71 Management0 - Dynamic Fwd |
受影響的產品
PowerSwitch E3200-ON Series, Dell EMC Networking N3200-ON, PowerSwitch S5212F-ON, PowerSwitch S5224F-ON, PowerSwitch S5232F-ON, PowerSwitch S5248F-ON, PowerSwitch S5296F-ON, PowerSwitch Z9264F-ON, PowerSwitch Z9332F-ON, PowerSwitch Z9432F-ON文章屬性
文章編號: 000218168
文章類型: How To
上次修改時間: 16 10月 2023
版本: 3
向其他 Dell 使用者尋求您問題的答案
支援服務
檢查您的裝置是否在支援服務的涵蓋範圍內。