Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Configuring Options for Trunk Ports

802.1ad trunk ports may also be tagged members of a VLAN so that it can carry single and double-tagged traffic.

You can enable trunk ports to carry untagged, single-tagged, and double-tagged VLAN traffic by making the trunk port a hybrid port.

To configure trunk ports, use the following commands.

  1. Configure a trunk port to carry untagged, single-tagged, and double-tagged traffic by making it a hybrid port. INTERFACE mode portmode hybrid
    • NOTE: You can add a trunk port to an 802.1Q VLAN as well as a Stacking VLAN only when the TPID 0x8100.
  2. Add the port to a 802.1Q VLAN as tagged or untagged. INTERFACE VLAN mode [tagged | untagged]

Example of Configuring a Trunk Port as a Hybrid Port and Adding it to Stacked VLANs

In the following example, GigabitEthernet 0/1 is a trunk port that is configured as a hybrid port and then added to VLAN 100 as untagged VLAN 101 as tagged, and VLAN 103, which is a stacking VLAN. 
Dell(conf)#int gi 0/1
                                 Dell(conf-if-gi-0/1)#
                                 portmode hybrid
                                 Dell(conf-if-gi-0/1)#switchport
                                 Dell(conf-if-gi-0/1)#vlan-stack trunk
                                 Dell(conf-if-gi-0/1)#show config
                                 !
                                 interface GigabitEthernet 0/1
                                 no ip address
                                 portmode hybrid
                                 switchport
                                 vlan-stack trunk
                                 shutdown
                                 Dell(conf-if-gi-0/1)#interface vlan 100
                                 Dell(conf-if-vl-100)#untagged gigabitethernet 0/1
                                 Dell(conf-if-vl-100)#interface vlan 101
                                 Dell(conf-if-vl-101)#tagged gigabitethernet 0/1
                                 Dell(conf-if-vl-101)#interface vlan 103
                                 Dell(conf-if-vl-103)#vlan-stack compatible
                                 Dell(conf-if-vl-103-stack)#member gigabitethernet 0/1
                                 Dell(conf-if-vl-103-stack)#do show vlan
                                 
                                 Codes: * - Default VLAN, G - GVRP VLANs
                                 Q: U - Untagged, T - Tagged
                                 x - Dot1x untagged, X - Dot1x tagged
                                 G - GVRP tagged, M - Vlan-stack
                                 
                                 NUM    Status     Description  Q Ports
                                 * 1    Inactive
                                 100  Inactive                U Gi 0/1
                                 101  Inactive                T Gi 0/1
                                 103  Inactive                M Gi 0/1

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\