Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Customizing a Privilege Level

to customize a privilege level, use the following commands.

  1. Remove a command from the list of available commands in EXEC mode. CONFIGURATION mode privilege exec level level { command ||...|| command}
  2. Move a command from EXEC Privilege to EXEC mode. CONFIGURATION mode privilege exec level level { command ||...|| command}
  3. Allow access to CONFIGURATION mode. CONFIGURATION mode privilege exec configure level level
  4. Allow access to INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode. Specify all keywords in the command. CONFIGURATION mode privilege configure level level {interface | line | route-map | router} { command-keyword ||...|| command-keyword}
  5. Allow access to a CONFIGURATION, INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode command. CONFIGURATION mode privilege {configure |interface | line | route-map | router} level level { command ||...|| command}

Create a Custom Privilege Level Apply a Privilege Level to a Username

The following configuration privilege level 3. This level:
  • removes the resequence command from EXEC mode by requiring a minimum of privilege level 4
  • moves the capture bgp-pdu max-buffer-size command from EXEC Privilege to EXEC mode by requiring a minimum privilege level 3, which is the configured level for VTY 0
  • allows access to CONFIGURATION mode with the banner command
  • allows access to INTERFACE and LINE modes with the no command 
Dell(conf)#do show run privilege
                                 !
                                 Dell(conf)#privilege exec level 3 capture
                                 Dell(conf)#privilege exec level 3 configure
                                 Dell(conf)#privilege exec level 4 resequence
                                 Dell(conf)#privilege exec level 3 clear arp-cache
                                 Dell(conf)#privilege exec level 3 clear arp-cache max-buffer-size
                                 Dell(conf)#privilege configure level 3 line
                                 Dell(conf)#privilege configure level 3 interface
                                 Dell(conf)#do telnet 10.11.80.201
                                 [telnet output omitted]
                                 Dell#show priv
                                 Current privilege level is 3.
                                 Dell#?
                                 capture            Capture packet
                                 configure          Configuring from terminal
                                 disable            Turn off privileged commands
                                 enable             Turn on privileged commands
                                 exit               Exit from the EXEC
                                 ip                 Global IP subcommands
                                 monitor            Monitoring feature
                                 mtrace             Trace reverse multicast path from destination to source
                                 ping               Send echo messages
                                 quit               Exit from the EXEC
                                 show               Show running system information
                                 [output omitted]
                                 Dell#config
                                 [output omitted]
                                 Dell(conf)#do show priv
                                 Current privilege level is 3.
                                 Dell(conf)#?
                                 end                Exit from configuration mode
                                 exit               Exit from configuration mode
                                 interface          Select an interface to configure
                                 Dell(conf)#interface ?
                                 loopback           Loopback interface
                                 managementethernet Management Ethernet interface
                                 null               Null interface
                                 port-channel       Port-channel interface
                                 range              Configure interface range
                                 tengigabitethernet TenGigabit Ethernet interface
                                 vlan               VLAN interface
                                 Dell(conf)#interface tengigabitethernet 1/1
                                 Dell(conf-if-te-1/1)#?
                                 end                Exit from configuration mode
                                 exit               Exit from interface configuration mode
                                 Dell(conf-if-te-1/1)#exit
                                 Dell(conf)#line ?
                                 console Primary terminal line
                                 vty Virtual terminal
                                 Dell(conf)#line vty 0
                                 Dell(conf-line-vty)#?
                                 exit               Exit from line configuration mode
                                 Dell(conf-line-vty)#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\