Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Dell Financial Services Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.6

show ip ospf

Display information on the OSPF process configured on the switch.

Syntax
show ip ospf [process-id | vrf vrf name]
Parameters
process-id
Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
vrf vrf name
Show only the OSPF information tied to the VRF process.
Command Modes
  • EXEC
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.4.(0.0)
Added support for VRF.
9.2(1.0)
Introduced on the Z9500.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.8.0
Added output for LSA throttling timers.
8.3.7.0
Introduced on the S4810.
7.9.1.0
Added support for VRF.
7.8.1.0
Added support of Multi-Process OSPF.
7.8.1.0
Added the process-id option, in support of Multi-Process OSPF.
7.6.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
pre- 6.1.1.1
Introduced on the E-Series.
Usage Information
If you delete all the network area commands for Area 0, the show ip ospf command output does not list Area 0.

The following describes the show ip ospf command shown in the following example.

Line Beginning with
Description
“Routing Process...”
Displays the OSPF process ID and the IP address associated with the process ID.
“Supports only...”
Displays the number of Type of Service (TOS) rouse supported.
“SPF schedule...”
Displays the delay and hold time configured for this process ID.
“Convergence Level”
“Min LSA....”
Displays the intervals set for LSA transmission and acceptance.
“Number of...”
Displays the number and type of areas configured for this process ID.
Example
DellEMC# show ip ospf 10
Routing Process ospf 10 with ID 1.1.1.1 Virtual router default-vrf
Supports only single TOS (TOS0) routes
SPF schedule delay 5 secs, Hold time between two SPFs 10 secs
Convergence Level 0
Min LSA origination 0 msec, Min LSA arrival 1000 msec
Min LSA hold time 5000 msec, Max LSA wait time 5000 msec
Number of area in this router is 1, normal 1 stub 0 nssa 0
    Area BACKBONE (0)
      Number of interface in this area is 1
      SPF algorithm executed 205 times
      Area ranges are
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\