Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

show monitor session

Display information about monitoring sessions.

Syntax
show monitor session {session-ID} [access-list]

To display monitoring information for all sessions, use the show monitor session command.

Parameters
session-ID
(OPTIONAL) Enter a session identification number. The range is from 0 to 65535.
[access-list]
(OPTIONAL) Enter the access-list keyword to display the ACLs applied to monitor sessions.
Defaults
none
Command Modes
  • EXEC
  • as
  • EXEC Privilege
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.14(0.0)
Updated to display the IPv6 ACLs applied to monitor session on the S6000, S6000–ON, S5048F-ON, S6100–ON, and Z9100–ON.
9.12(0.0)
Introduced the access-list optional keyword to display the ACLs applied to monitor sessions on the S6000, S6100–ON and Z9100–ON.
9.11(0.0)
Introduced the support for GRE Protocol and FC Monitor in the command output.
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.7(0.0)
Introduced on the S6000-ON.
9.5(0.1)
Introduced on the Z9500.
9.4.0.0
Added support for the RPM / ERPM.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.7.0
Introduced on the S4810.
8.3.11.1
Introduced on the Z9000.
8.1.1.0
Introduced on the E-Series.
7.7.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
7.4.1.0
Introduced on the E-Series.
Example
DellEMC# show monitor session 1
SessID  Source         Destination         Dir  Mode  Source IP      Dest IP         DSCP  TTL   Drop  Rate    Gre-Protocol FcMonitor
------  ------         -----------         ---  ----  ---------      --------        ----  ---   ----  ----    -----------  ---------
   1    Te 1/2         remote-ip           rx   Port   0.0.0.0       0.0.0.0          0     0    No    N/A        N/A        yes
DellEMC#

DellEMC# show monitor session
SessID  Source         Destination         Dir  Mode  Source IP      Dest IP         DSCP  TTL   Drop  Rate    Gre-Protocol FcMonitor
------  ------         -----------         ---  ----  ---------      --------        ----  ---   ----  ----    -----------  ---------
   1    Te 1/2         remote-ip           rx   Port   0.0.0.0       0.0.0.0          0     0    No    N/A        N/A        yes
DellEMC#
Example (show monitor session access-list)

The following is an example output of the show monitor session access-list command.

DellEMC#sho monitor session 13 access-list
  Monitor session – 13
  Interface         Direction   Mirror-access-list
  ---------         ---------   ------------------
   Te 1/1           rx          mtacl
                                mtv6acl(ipv6)
Related Commands

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\