Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version

Description

9.13(0.0)

Updated to show mismatch in VXLAN instance parameters.

9.10(0.1)

Introduced on the S6010-ON and S4048T-ON.

9.10(0.0)

Introduced on the S3148.

9.10(0.0)

Introduced on the S6100–ON.

9.8(2.0)

Introduced on the S3100 series.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced support for Q-in-Q implementation over VLT on the S-Series and Z-Series. Introduced on the S6000-ON.

9.5(0.1)

Introduced on the Z9500.

9.2(0.2)

Introduced on the Z9000, S4810, and S4820T.

9.2(0.0)

Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only.

9.0.2.0

Introduced on the S6000.

DellEMC#show vlt mismatch
Domain
------
Parameters        Local              Peer
----------        -----              ----

Vlan-config
---------------------------------
Vlan-ID   Local Mode    Peer Mode
--------- ------------  ---------

      20             L2            --

Vlan IPV4 Multicast Status
--------------------------
  Vlan-ID        Local Status        Peer Status
  --------       ------------        -----------
  55              Inactive             Active

  1500            Inactive             Active

VLT-VXLAN config
 ---------------

  VLAN to VNI config mismatch
 --------------------------------------
  Vlan-ID      Local VNID     Peer VNID
 ---------       ------------   -----------
 10              10              -
 11              11              -
 12              12              -
 13              13              -                                                                                             



  VXLAN enabled status on VLT Port Channels
 -------------------------------------------
  Local-Lag    Status    Peer-Lag    Status
  ---------   --------   --------   --------
  300         Disable    100        Disable
  700         Enable     812        Disable
  999         Disable    888        Disable                                                                                 


Local VTEP IP mismatch
-------------------------------------------------------------------
Local Node “Local VTEP IP” 		Remote Node “Local VTEP IP”
10.1.1.1				20.1.1.1

  Remote VTEP Oper Status on VLT nodes
 ---------------------------------------------------------
  Remote  VTEP IP   Local-Oper-Status   Remote-Oper-Status
  ---------------   -----------------   ------------------
      66.66.66.66                  UP                 DOWN

DellEMC#show vlt mismatch
Domain 
------ 
Parameters    Local      Peer 
----------    -----      ---- 
PB for stp    Enabled    Disabled       

Vlan-type-config 
---------------- 
Codes:: P - Primary, C - Community, I - Isolated, N - Normal vlan, M - Vlan-stack

Vlan-ID		Local	Peer 
-------		-----	---- 

 100		    N	    M   

Port-type-config 
---------------- 
Codes:: p - PVLAN Promiscuous port, h - PVLAN Host port, t - PVLAN Trunk port, 
        mt - Vlan-stack trunk port, mu - Vlan-stack access port, n - Normal port

Vlt Lag		 Local	 Peer 
-------		 -----	 ---- 
128		     mt	    mu

Vlan-stack protocol-type 
------------------------ 

Local	  Peer 
-----	  ---- 
0x4100	  0x8100 

VLT-VLAN config 
--------------- 

Local Lag  Peer Lag Local VLANs	Peer VLANs
---------  -------- -----------	----------
 128         128       4094          100
                                               
DellEMC#