Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
Sign In Create an Account Dell Financial Services Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell Command Line Reference Guide for the S4048–ON System 9.14.2.4

PDF

source (port monitoring)

Configure a port monitor source.

Syntax
source {interface | range | any} destination interface direction {rx | tx | both}

To disable a monitor source, use the no source interface destination interface direction {rx | tx | both} command.

Parameters
source interface
Enter one of the following keywords and slot/port information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094.
  • For a port channel interface, enter the keywords port-channel then a number.
range
Enter the keyword range to specify the list of interfaces.
any
Enter the keyword any to specify all interfaces.
NOTE This option is applicable only with drop monitor session.
destination
Enter the keyword destination to specify the destination interface.
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a port channel interface, enter the keywords port-channel then a number.
interface
Enter one of the following keywords and slot/port information:
  • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
  • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
  • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
  • For a port channel interface, enter the keywords port-channel then a number.
direction {rx | tx | both}
Enter the keyword direction then one of the packet directional indicators.
  • rx: to monitor receiving packets only.
  • tx: to monitor transmitting packets only.
  • both: to monitor both transmitting and receiving packets.
Defaults
none
Command Modes
MONITOR SESSION (conf-mon- sess-session-ID)
Command History

This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.

Version
Description
9.10(0.1)
Introduced on the S6010-ON and S4048T-ON.
9.10(0.0)
Introduced on the S3148.
9.10(0.0)
Introduced on the S6100-ON.
9.8(2.0)
Introduced on the S3100 series.
9.8(1.0)
Introduced on the Z9100-ON.
9.8(0.0P5)
Introduced on the S4048-ON.
9.8(0.0P2)
Introduced on the S3048-ON.
9.8(0.0)
Added the any parameter.
9.7(0.0)
Introduced on the S6000-ON.
9.5(0.1)
Introduced on the Z9500.
9.4.0.0
Added support for Source and destination.
9.0.2.0
Introduced on the S6000.
8.3.19.0
Introduced on the S4820T.
8.3.11.1
Introduced on the Z9000.
8.3.7.0
Introduced on the S4810.
8.5.1.0
Added support for 4-port 40G line cards on the E-Series.
8.1.1.0
Introduced on the E-Series.
7.7.1.0
Introduced on the S-Series.
7.5.1.0
Introduced on the C-Series.
7.4.1.0
Introduced on the E-Series.
Example
DellEMC# monitor session 0
source Port-channel 10 destination TenGigabitEthernet 1/3 direction tx
DellEMC#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\