- Notes, cautions, and warnings
- Release summary
- Compatibility
- New and enhanced features
- Fixes
- Deprecated features
- Important notes
- Known issues — To be fixed in future releases
- Getting an error SWC0018 during OS installation
- WSMan query with space between attributes fails
- Attributes for CNA cards not displayed through Redfish or RACADM interface
- Rollback firmware Version is not displayed for NVDIMMs
- Get method not displaying certificates after all certificates are deleted
- iDRAC dashboard page in IE displays an expanded progress bar
- Unable to create a recurring job after same recurring job was completed
- Unable to create virtual disk through Redfish
- SCP Import Job completes with error due to HddSeq error
- iDRAC LC Log shows reset cause as ‘watchdog’
- Delayed response when iDRAC’s network settings are reconfigured
- Integrated/Embedded NIC displaying status as Unknown
- No errors when the selected component and the selected device firmware do not match
- SEL missed in the LCL during Racreset.
- PCIe SSD Backplane 2 is displayed as unknown
- Firmware update operation not scheduled through WSMan
- Access to serial interface fails.
- Delayed response when iDRAC's network settings are reconfigured
- Remote File Share (RFS) does not stay connected after downgrading iDRAC
- Boot Capture file does not have any content
- LC log created after going to Virtual media page in iDRAC GUI
- Firmware update for a replaced PSU failing
- Device description and type not displayed
- Get method on UefiTargetBootSourceOverride attribute shows null value
- Sluggishness in Virtual Console
- Blank boot capture file generated
- Unable to export factory shipped inventory
- NIC or FC device slot listed in hardware inventory even when disabled in BIOS
- Get operation not displaying model or serial number for PCIe devices
- iDRAC DUP update fails on SLES when secure boot is enabled
- Boot mode error during OS deployment
- Repetitive PR7 messages related to PSU in LC logs after a system erase operation
- After a warm reboot, LC logs display Disk Inserted
- Limitations
- Updating iDRAC firmware
- Lifecycle Controller Remote Services — client tools
- Resources and support
- Contacting Dell EMC
iDRAC9 Version 4.00.00.00 Release Notes
Automation — API and CLI
- Sometimes, when using WSMan, an Internal SSL Error is reported and the WSMan command fails. If this issue occurs, retry the command.
- Using WSMan, the attribute LCD.ChassisIdentifyDuration cannot be set to -1 (indefinite blink). To make the LED blink indefinitely, use the IdentifyChassis command with IdentifyState=1.
- RACADM supports the underscore character (_) for iDRAC.SerialRedirection.QuitKey along with the existing symbols shown in the integrated help.
- Using remote RACADM, if you use the racadm hwinventory export command to export the hardware inventory using an incorrect CIFS share, an incorrect message is displayed: RAC930 : Unable to export the hwinventory. If the issue persists, restart iDRAC and retry the operation after iDRAC has finished restarting.
- If iDRAC is in lockdown mode and you run the command 'racadm rollback', followed by the command 'racadm resetcfg', an incorrect message is displayed: ERROR: A firmware update is currently in progress. Unable to reset the RAC at this time. Reboot iDRAC to display the correct error message.
- While using a Top or Skip command, if you enter a value greater than the unsigned long type (4,294,967,295), you may get an incorrect error message.
- You cannot use the FQDD of iDRAC (iDRAC.Embedded.1) when changing iDRAC mode from Shared LOM to Dedicated.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\