- Notes, cautions, and warnings
- Additional Resources
- Introduction
- Import requirements and restrictions
- General requirements for importing data
- Dell EqualLogic PS Series specific requirements
- Dell Compellent SC Series specific requirements
- Dell Unity specific requirements
- Dell VNX2 Series specific requirements
- Dell XtremIO XI and X2 specific requirements
- Dell PowerMax and VMAX3 specific requirements
- NetApp AFF A-Series specific requirements
- General block-based import restrictions
- General file-based import restrictions
- Host plugin installation (block-based non-disruptive import only)
- Installing the host plugin for import on a Windows-based host
- Installing the host plugin for import on a Linux-based host
- Installing the Dell EqualLogic MEM kit on an ESXi-based host
- Install the Dell EqualLogic MEM kit on an ESXi-based host using the vSphere CLI
- Install the Dell EqualLogic MEM kit on an ESXi-based host using setup.pl script on VMA
- Install the Dell EqualLogic MEM kit on an ESXi-based host using VUM
- Install the Dell EqualLogic MEM kit during an ESXi-based host upgrade
- Uninstalling the host plugin for import
- Import workflows
- Non-disruptive import workflow
- Cutover workflow for non-disruptive import
- Cancel workflow for non-disruptive import
- Agentless import workflow
- Cutover workflow for agentless import
- Cancel workflow for agentless import
- File-based import workflow
- Cutover workflow for file-based import
- Cancel workflow for file-based import
- Configuring and managing import
- Configure a non-disruptive import
- Refresh hosts and volumes in a non-disruptive import
- Manage non-disruptive import sessions
- Configure an agentless import
- Configure an agentless import for a Universal type remote system
- Manage agentless import sessions
- Configure a File Mobility Network for file-based import
- Configure the connection to a remote system for file-based import
- Configure file import interface
- Configure a file-based import
- Manage file-based import sessions
- Import-CLI (Linux)
- Additional tasks related to import for Linux-based hosts
- ImportKit-CLI (Windows)
- How to run the ImportKit CLI commands
- List supported arrays
- Host plugin log information
- Import kit version
- Restart import kit host plugin service
- Import volumes information
- Get web server port information
- Install import kit certificate
- Regenerate the import kit certificate
- Set web server port information
- Set host plugin logging debug log level
- Import-CLI (VMware)
- CLI for EQL MPIO
- Fault handling by PowerStore import
Dell PowerStore Importing External Storage to PowerStore Guide
Dell EqualLogic PS Series specific requirements
(For non-disruptive import) See the PowerStore Simple Support Matrix document at dell.com/powerstoredocs for the supported combinations of host operating system, host multipath software, and host protocol that apply to Dell EqualLogic Peer Storage (PS) Series systems.
NOTE:(For non-disruptive import) If you are not running the Dell EqualLogic Host Integration Tools Kit, you can use the
PowerStore cluster ImportKIT which uses native MPIO.
(For agentless import) See the PowerStore Simple Support Matrix document at dell.com/powerstoredocs for the supported types of source systems and the version of operating environment that is required for the agentless import.
NOTE:All hosts taking part in an import process should have initiator names in the standard IQN format of
iqn.yyyy-mm.naming-authority:unique name. Although PS source systems support friendly names, such as *.*.*.* or 172.92.*.* for the standard IQN format,
PowerStore only supports valid standard IQN format. Import fails when friendly IQN names are used. In this case, the initiator names must be changed to valid full IQN names on all the associated hosts before attempting an import of external storage to
PowerStore.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\