Dell PowerStore Hardware Information Guide for PowerStore 1000, 1200, 3000, 3200, 5000, 5200, 7000, 9000, and 9200

PDF

Power requirements for the base enclosure

Power requirements vary depending on system configuration, loading, and environmental conditions. The table below describes the maximum expected power draw. To estimate power consumption values for your specific environment, use the Dell Power Calculator.

Table 1. Power requirements for x000 modelsColumn one lists the requirements, and the other columns list the x000 models.
Requirement	1000T	3000T	5000T	7000T	9000T
Maximum input power	240 VAC ± 10%, single phase For 100-120V, a customer-supplied step-up transformer is required.
AC Line Current (operating maximum at 200 VAC)	6.7 A	8.1 A	9.0 A	9.3 A	10.4 A
Power Consumption (operating maximum at 200 VAC)	1385 VA (1316 W)	1629.6 VA (1597 W)	1792.9 VA (1757 W)	1868.4 VA (1831 W)	2088.8 VA (2047 W)
Heat Dissipation (operating maximum)	4.73 x 10⁶ J/hr, (4,490 Btu/hr)	5.74 x 10⁶ J/hr, (5,449 Btu/hr)	6.32 x 10⁶ J/hr, (5,995 Btu/hr)	6.59 x 10⁶ J/hr, (6,248 Btu/hr)	7.37 x 10⁶ J/hr, (6,985 Btu/hr)
AC Inlet type	IEC320-C14 or IEC320-C20 appliance coupler per power zone			IEC320-C20 appliance coupler per power zone
Normal input frequency	47 Hz–63 Hz
Maximum inrush current	45 Apk "cold" per line cord at any line voltage
AC protection	20 A fuse on each power supply, single line
Ride-through time	10 ms min
Current sharing	± 5 percent of full load between power supplies
Startup Surge Current	120 Apk "hot" per line cord, at any line voltage

Table 2. Power requirements for x200 modelsColumn one lists the requirements, and the other columns list the x200 models.
Requirement	1200T	3200T	3200Q	5200T	9200T
Maximum input power	240 VAC ± 10%, single phase For 100-120V, a customer-supplied step-up transformer is required.
AC Line Current (operating maximum at 200 VAC)	6.5 A	7.1 A	7.7 A	8.8 A	9.8 A
Power Consumption (operating maximum at 200 VAC)	1297.2 VA (1271.3 W)	1422 VA (1393.6 W)	1535.8 VA (1505.1 W)	1769.8 VA (1734.4 W)	1958.6 VA (1919.4 W)
Heat Dissipation (operating maximum)	4.58 x 10⁶ J/hr, (4,338 Btu/hr)	5.02 x 10⁶ J/hr, (4,755 Btu/hr)	5.42 x 10⁶ J/hr, (5,136 Btu/hr)	6.24 x 10⁶ J/hr, (5,918 Btu/hr)	6.91 x 10⁶ J/hr, (6,549 Btu/hr)
AC Inlet type	IEC320-C14 or IEC320-C20 appliance coupler per power zone				IEC320-C20 appliance coupler per power zone
Normal input frequency	47 Hz–63 Hz
Maximum inrush current	45 Apk "cold" per line cord at any line voltage
AC protection	20 A fuse on each power supply, single line
Ride-through time	10 ms min
Current sharing	± 5 percent of full load between power supplies
Startup Surge Current	120 Apk "hot" per line cord, at any line voltage

Table 3. High ambient temperature shutdownColumn one lists the ambient temperature, and the other columns list the hardware faults and consequences.
Ambient temperature	Hardware fault	Consequence
Above 45° C (113° F)	None	Noncritical warning generated.
Above 50° C (122° F)	None	Critical alert generated. The system shuts down after five minute timer expires. If the temperature returns to less than 45° C (113° F) , the system powers on.
Any	Three hottest drives have an average temperature of 50° C (122° F)	The system shuts down after five minute timer expires.
Any	Two fans fault	The system shuts down after five minute timer expires.