- Notes, Cautions, and Warnings
- About This Guide
- About the SCv3000 and SCv3020 Storage System
- Storage Center Hardware Components
- Storage Center Communication
- Front-End Connectivity
- Back-End Connectivity
- System Administration
- Storage Center Replication
- SCv3000 and SCv3020 Storage System Hardware
- SCv3000 and SCv3020 Storage System Front-Panel View
- SCv3000 and SCv3020 Storage System Back-Panel View
- Expansion Enclosure Overview
- Install the Storage Center Hardware
- Connect the Front-End Cabling
- Types of Redundancy for Front-End Connections
- Connecting to Host Servers with Fibre Channel HBAs
- Connecting to Host Servers with iSCSI HBAs or Network Adapters
- Connecting to Host Servers with SAS HBAs
- Attach Host Servers (Fibre Channel)
- Attach the Host Servers (iSCSI)
- Attach the Host Servers (SAS)
- Connect the Management Ports to the Management Network
- Connect the Back-End Cabling
- Deploy the Storage Center
- Preparing for Deployment
- Deploying the Storage Center Using Unisphere
- Unisphere Discovery Utility
- Deploying the Storage Center Using Storage Manager Client
- Install and Use the Storage Manager Client
- Introduction to Storage Center Initial Configuration
- Select a Storage Center to Initialize
- Welcome Page
- Customer Installation Authorization
- Set System Information
- Set Administrator Information
- Confirm the Storage Center Configuration
- Deploy the Storage Center
- Configure Key Management Server Settings
- Create a Storage Type
- Fault Tolerance
- Inherit Settings
- Configure Time Settings
- Configure SMTP Server Settings
- Set Up SupportAssist
- Accept the SupportAssist Collection Agreement
- Provide Contact Information
- Provide Site Contact Information
- Validate the SupportAssist Connection
- Update Storage Center
- Complete Configuration and Perform Next Steps
- Perform Post-Setup Tasks
- Adding or Removing Expansion Enclosures
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Install New SCv300 and SCv320 Expansion Enclosures in a Rack
- Add the SCv300 and SCv320 Expansion Enclosures to the A-Side of the Chain
- Add the SCv300 and SCv320 Expansion Enclosures to the B-Side of the Chain
- Install New SCv360 Expansion Enclosures in a Rack
- Add the SCv360 Expansion Enclosures to the A-Side of the Chain
- Add an SCv360 Expansion Enclosure to the B-Side of the Chain
- Adding a Single Expansion Enclosure to a Chain Currently in Service
- Removing an Expansion Enclosure from a Chain Currently in Service
- Release the Drives in the Expansion Enclosure
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv300 and SCv320 Expansion Enclosure from the B-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the A-Side of the Chain
- Disconnect the SCv360 Expansion Enclosure from the B-Side of the Chain
- Adding Expansion Enclosures to a Storage System Deployed Without Expansion Enclosures
- Troubleshooting Storage Center Deployment
- Set Up a Local Host or VMware Host
- Worksheet to Record System Information
SCv3000 and SCv3020 Storage System Deployment Guide
Install and Use the Storage Manager Client
Start the Storage Manager Client as an Administrator to run the Discover and Configure Uninitialized Storage Centers wizard.
Steps
-
Install the
Storage Manager Client on a host server.
To discover and configure a Storage Center, the software must be installed on a host server that is on the same subnet as the storage system.
- To start the Storage Manager Client on a Windows computer, right-click the Dell Storage Manager shortcut and select Run as administrator. To start the Storage Manager Client on a Linux computer, run the command ./Client from the var/lib/dell/bin directory.
- Click Discover and Configure Uninitialized . The Discover and Configure Uninitialized wizard starts.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\