Before
installing or running the iDRAC Service Module, should the Open Manage
Server Administrator be uninstalled?
No you
do not have to uninstall Server Administrator. Before you install
or run the iDRAC Service Module, make sure that you have stopped the
features of Server Administrator that the iDRAC Service Module provides.
How
to check whether iDRAC Service Module is installed in the system?
To know if the iDRAC Service Module is installed on the system,
- On Windows:
Run the
service.msc command. In
the list of services displayed, see if there is a service called
DSM iDRAC Service Module.
- On Linux:
Run the command
/etc/init.d/dcismeng status. If the iDRAC Service Module is installed and running, the status
displayed is
running.
-
NOTE: Use the
systemctl status dcismeng.service command instead of the
init.d command to check if the iDRAC Service Module is installed
on RedHat Enterprise Linux 7 operating system.
How
to check the version number of the iDRAC Service Module installed
in the system?
To check the version of the iDRAC Service Module
in the system, do any of the following:
- Click
. The version of the installed iDRAC Service Module
is listed in the
Version tab.
- Go to
.
What
is the minimum permission level required to install the iDRAC Service
Module?
To install the iDRAC Service Module, you must have
administrator level privileges.
While
installing the iDRAC Service Module, it displays an error message
This is not a supported server. Consult the User Guide
for additional information about the supported servers. How to resolve
this?
Before installing the iDRAC Service Module, make sure
that the server is a 12th generation PowerEdge sever or later. Also,
make sure that you have a 64-bit system.
The
following message is displayed in the OS log, even when the OS to
iDRAC Pass-through over USBNIC is configured properly. Why?
The iDRAC Service Module is unable to communicate with iDRAC using the OS to iDRAC Pass-through channel
iDRAC Service Module uses the OS to iDRAC pass-through over USB
NIC feature to establish the communication with iDRAC. Sometimes,
the communication is not established though the USB NIC interface
is configured with the correct IP endpoints. This may happen when
the host operating system routing table has multiple entries for the
same destination mask and the USB NIC destination is not listed as
the first one in routing order.
Destination |
Gateway |
Genmask |
Flags |
Metric |
Ref |
Use Iface |
default |
10.94.148.1 |
0.0.0.0 |
UG |
1024 |
0 |
0 em1 |
10.94.148.0 |
0.0.0.0 |
255.255.255.0 |
U |
0 |
0 |
0 em1 |
link-local |
0.0.0.0 |
255.255.255.0 |
U |
0 |
0 |
0 em1 |
link-local |
0.0.0.0 |
255.255.255.0 |
U |
0 |
0 |
0 enp0s20u12u3 |
In the example
enp0s20u12u3 is the USB NIC interface.
The link-local destination mask is repeated and the USB NIC is not
the first one in the order. This results in the connectivity issue
between iDRAC Service Module and iDRAC over the OS to iDRAC Pass-through.
To troubleshoot the connectivity issue, make sure that the iDRAC USBNIC
IPv4 address (by default it is 169.254.0.1) is reachable from the
host operating system.
If not:
- Change the iDRAC USBNIC address on a unique destination mask.
- Delete the entries that are not required from the routing table
to make sure that USB NIC is chosen by route when the host wants to
reach the iDRAC USB NIC IPv4 address.
When
uninstalling iDRAC Service Module from a VMware ESXi server, the virtual
switch is named as vSwitchiDRACvusb and port group as iDRAC Network
on the Vsphere client. How to delete them?
While installing
iDRAC Service Module VIB on a VMware ESXi server, iDRAC Service Module
creates the vSwtich and Portgroup to communicate with iDRAC over the
OS to iDRAC Pass-through in USB NIC mode. After the uninstallation,
the virtual switch
vSwitchiDRACvusb and the
port group
iDRAC Network are not deleted. To
delete it manually, perform one of the following steps:
- Go to vSphere Client Configuration wizard and delete the entries.
- Go to the Esxcli and type the following commands:
- To remove port group:
esxcfg-vmknic -d -p "iDRAC Network"
- To remove vSwitch:
esxcfg-vswitch -d vSwitchiDRACvusb
-
NOTE: You can
reinstall iDRAC Service Module on the Vmware ESXi server as this is
not a functional issue for the server.
Where
is the Replicated LifeCycle log available on the Operating System?
To view the replicated Lifecycle logs:
Operating System |
Location |
Microsoft Windows |
. All the iDRAC Service Module Lifecycle logs are replicated under
the source name
iDRAC Service Module.
|
Red Hat Enterprise Linux , SUSE Linux, CentOS,
and Citrix XenServer
|
/var/log/messages
|
VMware ESXi |
/var/log/syslog.log
|
What
are the Linux dependent packages or executables available for installation
while completing the Linux installation?
To see the list of
Linux dependent packages, see the
Linux Dependencies section
in the
iDRAC Service Module Installation Guide.